Shop

Loaded Series · Datasheet

Audiomobile GTS 2112 Box: Loaded Sealed 12" Slim Enclosure Limited Edition · Single 12" Sealed enclosure

Net volume
0.78 cu ft
External dimensions
26.50" W x 14.25" H x 8.00" D
Buy at Audio IntensityFactory-direct, ships from Tullahoma
Audiomobile GTS 2112Buy at Audio Intensity
  • Best For: Shallow-Depth Trunk and Behind-Seat Builds, One-Off Limited Unit
  • Net Volume: 0.78 cu ft (0.89 cu ft Gross)
  • Driver Match: Audiomobile GTS 2112 S2 (included, wired and loaded)
  • Construction: Sealed Slim Profile | V-Groove/Dado | Double 1.5" Baffle | Recessed Sides | Grille Included

Spec of record

Technical specifications

SpecificationValue
SeriesProline X Performance Optimized, Limited Build
Driver IncludedAudiomobile GTS 2112 S2 (single 2 ohm)
Grille IncludedAudiomobile GSE 1012
External Dimensions26.50" W x 14.25" H x 8.00" D
Net Volume0.78 cu ft
Gross Volume0.89 cu ft
System Q (Qtc)1.02
System Resonance (Fc)45.7 Hz
Anechoic F335.5 Hz
Amplifier Power280 to 400 W RMS at 2 ohms
Final Impedance2 ohms
Baffle1.5" double layer
Panel Thickness0.75"
Side PanelsRecessed 0.50" into the shell
Face DetailHexagon routed into the baffle, trunkliner wrapped into the groove
Terminal Cup1, side mounted
DampingPolyfill, installed
CoveringDark Gray Trunkliner
MaterialLangboard Elite MDF
Shipping Weight48 lb
Warranty1 Year
BuiltTullahoma, Tennessee

Modeled response

Performance in this enclosure

Net airspace
0.78
cu ft
System Qtc
1.02
sealed
Half power
35.5
Hz · F3
Xmax at
575
W RMS · no filter
With 25 Hz subsonic
614
W RMS · +7%
Amplifier
400
W RMS recommended
This enclosure holds 0.78 cu ft net . In it the Audiomobile GTS 2112 runs a system Qtc of 1.02 with half power at 35.5 Hz, and the cone reaches its 14.2 mm travel limit at 575 W, above the driver’s 400 W thermal rating, so heat stops you before travel does. Run a subsonic filter at 25 Hz and that becomes 614 W — +39 W, or 7 percent more power for the same 14.2 mm of travel.

01Is it a sealed driver?

Efficiency bandwidth product places the motor before anything else is decided.

EBP = Fs ÷ Qes = 38.5
SEALED 0–50 TRANSITION 50–100 PORTED 100–150 0 50 100 150 single 2 ohm 38.5
single 2 ohm · EBP 38.5
EBP under 50 means a motor that wants a sealed load. The GTS 2112 sits at 38.5, inside that band, which is why this is a sealed build rather than a ported one.

02What the box does to it

0.78 cu ft against a 51.6 L Vas.

α = Vas ÷ Vb = 2.34  ·  Fc = Fs√(α+1) = 46 Hz  ·  Qtc = 1.02
20 30 50 70 100 150 200 +6 +0 -6 -12 -18 -24 FREQUENCY · Hz LEVEL · dB −3 dB
single 2 ohm · Qtc 1.02, Fc 46 Hz, F3 35.5 Hz
The box lifts resonance from 25.0 Hz free-air to 46 Hz and half power lands at 35.5 Hz, anechoic, before any cabin gain. Parameters are the published Audiomobile figures carried on our own GTS 2112 listing; Audiomobile publish no specification sheet, manual or per-model page for this driver. The set reproduces its own printed Qts from Qes and Qms to within 0.2 percent, and its own printed Cms and Mms from Vas and Sd to within 0.6 and 1.9 percent, so it is internally consistent. Audiomobile publish no basket displacement, so 0.10 cu ft is estimated and the net volume carries that estimate. Power is the 400 watts RMS printed on the motor label. This driver’s Qts of 0.56 puts a 0.707 alignment out of reach in any cabinet that would fit a trunk, so the Qtc plotted here is the one it actually lands on.

03The watts that reach Xmax (in this enclosure)

Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 14.2 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.

PXmax = 575 W unfiltered  →  614 W with a 25 Hz subsonic
20 30 50 70 100 150 200 0 4 8 12 16 FREQUENCY · Hz CONE TRAVEL · mm PAST LINEAR TRAVEL · Xmax 14.2 mm 575 W reaches Xmax here
single 2 ohm · 575 W, no filtersingle 2 ohm · 614 W with subsonic at 25 Hz, 24 dB/octXmax 14.2 mm one-way
Every trace touches the limit and no further, because each is drawn at the exact power that puts that coil on 14.2 mm. Unfiltered that is 575 W, reached first at 33 Hz. It sits above the 400 W the driver can take thermally, so the voice coil gives up before the suspension does. The dashed traces are the same driver behind a subsonic filter at 25 Hz, 24 dB/oct: stopping the cone wasting travel below the passband lets it take 614 W before hitting the same 14.2 mm. That is 7 percent more amplifier for the price of one filter setting.
ParamValueUnitNote
Fs25.00Hzfree-air resonance
Qts0.560single 2 ohm
Vas51.60Lequivalent compliance
Sd499.0cm²effective piston area
Xmax14.2mmone-way, as Audiomobile publish it
Pe400Wcontinuous RMS
SPL82.8dB1 W / 1 m, derived from T/S

Driver parameters as published by Audiomobile published specifications. Curves computed against this enclosure’s actual net airspace.

From the shop floor

Installer's take

Read the Qtc before you read anything else. 1.02 is not a typo and it is not something we are hiding: the GTS 2112 has a Qts of 0.56, and a driver carrying that much total Q does not go into a small sealed box and come out maximally flat. Butterworth would take 3.07 cubic feet. Audiomobile themselves say 0.75 to 1.25, and the launch release for this exact model says 0.75. We built 0.78 and we are printing the number that falls out of it.

What that sounds like: punchy, forward, loud for 0.78 cubic feet, with a rise around 45.7 Hz that most people hear as impact rather than as a peak. It is not the alignment for someone chasing 30 Hz in a hatchback. It is the alignment for someone who has 8 inches of depth to work with and wants a 12 in it.

Two notes on the figures. Audiomobile publish no displacement for the GTS 2112, so 0.10 cubic feet is our estimate and the net volume carries that estimate with it. And the motor label prints 400 watts RMS, which is the figure used throughout this page; set gain against that.

Before you order

Questions

Is the subwoofer included, and what else comes with it?

Yes. This is a loaded enclosure and it ships with the Audiomobile GTS 2112 S2 already mounted to the 1.5 inch double baffle and wired to the side mounted terminal cup. The Audiomobile GSE 1012 grille is fitted over the driver and the cabinet is packed with polyfill. You supply the speaker wire from your amplifier to the cup, and the amplifier itself.

Why 0.78 cubic feet, and what alignment does that target?

Audiomobile publish a 0.75 to 1.25 cubic foot sealed range for the GTS 2112, and the 2013 GTS launch release names 0.75 cubic feet for the 2112 specifically. At 0.78 cubic feet net this cabinet sits at the small end of that range. With a Qts of 0.56 the resulting system Q is 1.02, system resonance 45.7 Hz, anechoic half power 35.5 Hz. A maximally flat Qtc of 0.707 would require 3.07 cubic feet, which no trunk enclosure for a 5.4 inch deep driver is going to provide.

What amplifier should I use, and what impedance does it present?

280 to 400 watts RMS at 2 ohms. The GTS 2112 S2 is a single 2 ohm voice coil, so the load is fixed at 2 ohms and there is no series or parallel wiring decision to make. Check that your amplifier is rated for a 2 ohm load before connecting it. Set gain against the 400 watt RMS figure printed on the motor label rather than against a peak or maximum number.

Why is the cabinet only 8 inches deep?

Because the GTS 2112 only needs 5.4 inches of mounting depth. Behind the 0.75 inch shell face sits a 1.5 inch double baffle, and behind the motor is a 0.75 inch rear panel, which leaves 1.1 inches of air between the back of the magnet and the rear wall. An 8 inch overall depth is what that stack allows, and it is what lets a 12 go where a conventional 12 inch enclosure will not.

Why a double 1.5 inch baffle on a cabinet this small?

The baffle is the panel the driver pushes against, so it is the one that most needs to stay still. Two laminated 0.75 inch layers give the GTS 2112 a full 1.5 inches to bolt into and move the baffle's own resonance well clear of the 45.7 Hz system resonance. In a cabinet holding only 0.78 cubic feet of air, panel flex is a larger share of total compliance than it would be in a big box, so it matters more here, not less.

What is the real low end in a vehicle?

The 35.5 Hz anechoic half power figure is measured with no vehicle around it. In a sedan trunk, cabin gain adds output below roughly 50 Hz and rises as frequency falls, so usable in car response runs below the anechoic number. The Qtc of 1.02 puts a lift around 45.7 Hz, which reads as midbass punch and apparent loudness rather than as deep extension.

Is there polyfill in it, and should I add more?

It is already packed with polyfill and it should be left alone. Every sealed Proline X enclosure ships with fill. In a cabinet this tight the fill is doing real work, making the box behave as though it holds slightly more air than it measures, which pulls the system Q a little below the 1.02 geometric figure.

What does the hexagon on the face actually look like?

It is routed into the MDF baffle as a groove, and the Dark Gray Trunkliner is wrapped down into it. The pattern reads as relief in the carpet, catching light at an angle rather than standing out as a contrasting color. It is not a printed graphic, a decal or an acrylic insert, and it does not break the carpet surface.

Same series, same size

Other Loaded Series models