Shop
Proline X PO 10Q-S W EVL10 sealed wedge enclosure, product photos pending. Placeholder graphic reading Photos Coming Soon.

Performance Optimized · Datasheet

Performance Optimized Wedge Wide Sealed Quad 10" Enclosure Skar Audio EVL-10 · Quad 10" Sealed enclosure

Net volume
0.732 cu ft per driver, 2.93 cu ft total, after the divider and an estimated 0.092 cu ft displacement per driver
Max mounting depth
7.16 in required; 0.75 in clearance above the motor against the raked rear panel
External dimensions
44 in W × 17 in at the seat face H × 15.11 in at the base D
Front baffle
1.5 in double baffle, frames face mounted
Buy at Audio IntensityFactory-direct, ships from Tullahoma
Skar Audio EVL-10Buy at Audio Intensity
  • Best For: Quad Skar Audio EVL-10 SUV Cargo-Floor Builds
  • Net Volume: 0.732 cu ft per Driver (2.93 cu ft Net Total)
  • Driver Match: Four Skar Audio EVL-10 (Dual 2 Ohm / Dual 4 Ohm), matched
  • Construction: 2 Chambers | 44" Wide Wedge | V-Groove/Dado | Double 1.5" Baffle | 2 Terminal Cups

Spec of record

Technical specifications

SpecificationValue
SeriesProline X Performance Optimized Wedge Wide
Compatible DriverSkar Audio EVL-10, quantity 4, matched. Direct fit
ConfigurationQuad 10 inch sealed wedge, 2 chambers, 2 drivers per chamber
Mounting PositionSUV cargo floor, raked face against the rear seat back
Firing DirectionRearward toward the liftgate. Not a down fire design
External Width44 in
External Height17 in at the seat face
External Depth15.11 in at the base, tapering to 8.93 in at the top
Internal Volume, Gross3.36 cu ft total
Internal Volume, Net Acoustic0.732 cu ft per driver, 2.93 cu ft total, after the divider and an estimated 0.092 cu ft displacement per driver
Driver Mounting Depth7.16 in required; 0.75 in clearance above the motor against the raked rear panel
Alignment Per DriverEVL-10 D2 Qtc 0.680, fc 50.7 Hz, F3 52.8 Hz; EVL-10 D4 Qtc 0.711, fc 51.6 Hz, F3 51.3 Hz anechoic
Woofer Openings4 at 9.400 in
Woofer LayoutStaggered on the height, outer pair low, inner pair high
Frame Outer Diameter10.89 in
Fs / Qts / Qes / Qms44.0 Hz / 0.590 / 0.660 / 5.440
Vas / Sd / Xmax6.8 L / 314 cm2 / 24 mm
Driver Power Handling1000 W RMS per driver, 4000 W RMS for the set of 4 (thermal rating)
Recommended Amplifier700-1000 W RMS per driver, 2,800-4,000 W RMS for the full set
Parameter SourceSkar Audio published specifications
MaterialLangboard Elite MDF
ConstructionCNC cut, V-groove and dado joinery
Panel Thickness0.75 in
Front Baffle1.5 in double baffle, frames face mounted
Internal BracingOne full-height 3/4 in divider
Driver MountingThreaded inserts, stainless machine screws included
Terminal CupsTwo Proline X ABS and carbon fiber composite, side mounted, one per chamber, pre wired 12 gauge OFC
Acrylic InsertGloss black acrylic baffle insert standard
DampingLight polyfill wall lining in every chamber, does not alter acoustic volume
CarpetPlush black
Shipping Weight76 lb
Warranty1 Year Limited
Built InTullahoma, Tennessee

Modelled response

Performance in this enclosure

Net airspace
0.732
cu ft per driver
System Qtc
0.68–0.71
sealed
Half power
51.3–52.8
Hz · F3
Xmax at
1933
W RMS per driver · no filter
With 25 Hz subsonic
2548
W RMS per driver · +32%
Amplifier, per driver
700–1000
W RMS recommended
This enclosure holds 0.732 cu ft net per driver. In it the Skar Audio EVL-10 D2 runs a system Qtc of 0.68–0.71 with half power at 51.3–52.8 Hz, and the cone reaches its 23.5 mm travel limit at 1933 W per driver, above the driver’s 1000 W thermal rating, so heat stops you before travel does. Run a subsonic filter at 25 Hz and that becomes 2548 W per driver — +615 W, or 32 percent more power for the same 23.5 mm of travel.

00Sizing the amplifier

Every wattage on this panel is per driver. This cabinet holds four, so the amplifier feeds all four at once.

Per driver 700–1000 W RMS  ×  4 drivers  =  full set 2,800–4,000 W RMS
Look for a mono amplifier rated 2,800–4,000 W RMS at the load your coil version wires to. The top is the driver’s 1000 W thermal rating; with the 25 Hz subsonic set the cone still has travel to spare there, reaching Xmax only at 2548 W. Below the bottom of the range it will play, just with less headroom; above the top you are buying power the drivers cannot use.

01Is it a sealed driver?

Efficiency bandwidth product places the motor before anything else is decided.

EBP = Fs ÷ Qes = 65.2–66.7
SEALED 0–50 TRANSITION 50–100 PORTED 100–150 0 50 100 150 Dual 2 Ohm 66.7 Dual 4 Ohm 65.2
Dual 2 Ohm · EBP 66.7Dual 4 Ohm · EBP 65.2
At 65.2–66.7 the EVL-10 D2 sits in the transition band, not the sealed band. That is not a mismatch: a transition motor works in either alignment, and sealed buys a smaller box and a gentler roll-off at the cost of some low-end output. Stage 02 shows what this airspace actually does with it.

02What the box does to it

0.732 cu ft against a 6.8 L Vas.

α = Vas ÷ Vb = 0.33  ·  Fc = Fs√(α+1) = 51–52 Hz  ·  Qtc = 0.68–0.71
20 30 50 70 100 150 200 +6 +0 -6 -12 -18 -24 FREQUENCY · Hz LEVEL · dB −3 dB
Dual 2 Ohm · Qtc 0.68, Fc 51 Hz, F3 52.8 HzDual 4 Ohm · Qtc 0.71, Fc 52 Hz, F3 51.3 Hz
The box lifts resonance from 44.0–45.0 Hz free-air to 51–52 Hz and half power lands at 51.3–52.8 Hz, anechoic, before any cabin gain. Figures are Skar Audio’s published parameters; Qes and Qms reproduce the printed Qts. This cabinet holds four drivers in two sealed chambers of 1.465 cubic feet, two drivers to a chamber, so each driver works into 0.732 cubic feet and that is the volume plotted here.

03The watts that reach Xmax (in this enclosure)

Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 23.5 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.

PXmax = 1933–2055 W per driver unfiltered  →  2548–2583 W with a 25 Hz subsonic
20 30 50 70 100 150 200 0 8 16 24 FREQUENCY · Hz CONE TRAVEL · mm PAST LINEAR TRAVEL · Xmax 23.5 mm 1933 W reaches Xmax here
Dual 2 Ohm · 1933 W, no filterDual 4 Ohm · 2055 W, no filterDual 2 Ohm · 2548 W with subsonic at 25 Hz, 24 dB/octDual 4 Ohm · 2583 W with subsonic at 25 Hz, 24 dB/octXmax 23.5 mm one-way
Every trace touches the limit and no further, because each is drawn at the exact power that puts that coil on 23.5 mm. Unfiltered that is 1933 W per driver, reached first at 20 Hz. It sits above the 1000 W the driver can take thermally, so the voice coil gives up before the suspension does. The dashed traces are the same driver behind a subsonic filter at 25 Hz, 24 dB/oct: stopping the cone wasting travel below the passband lets it take 2548 W per driver before hitting the same 23.5 mm. That is 32 percent more amplifier for the price of one filter setting.
ParamValueUnitNote
Fs44.00 / 45.00Hzfree-air resonance
Qts0.590 / 0.620Dual 2 Ohm / Dual 4 Ohm
Vas6.80 / 6.50Lequivalent compliance
Sd314.1cm²effective piston area
Xmax23.5mmone-way linear travel
Pe1000Wcontinuous RMS
SPL81.3dB1 W / 1 m, derived from T/S

Driver parameters as published by Skar Audio EVL-10 D2 / EVL-10 D4 published specifications. Curves computed against this enclosure’s actual net airspace.

From the shop floor

Installer's take

Start with the size. 0.732 cubic feet per driver puts the EVL-10 at Qtc 0.680, resonance 50.7 Hz, half power 52.8 Hz anechoic. The 7.16 in deep motor sets the shallowest the wedge can be, and that smallest box is still more air than flat wants, so it lands below 0.707: tighter and more damped, trading a little extension for control. One box serves every coil version: the Dual 2 Ohm at Qtc 0.680, the Dual 4 Ohm at Qtc 0.711.

Measure the base depth, not the top. This cabinet is 15.11 in deep where it meets the floor, 8.93 at the top, 44 wide and 17 tall. In an SUV the 44 has to clear between the rear wheel wells at floor height, the base depth is measured from the seat back with the seat upright and latched, and the 17 has to clear the cargo cover.

The two terminal cups are on the side panels, one per chamber, so they sit close to the wheel wells. Land the speaker wire on both before the box slides into its final spot, with slack to pull it forward again.

Two drivers share each chamber, so they have to match: same model, same coil, wired in phase. One driver reversed in a shared chamber pushes against its partner and the pair cancels instead of adding. Check polarity at each cup with a battery tap before the box goes in. The outer pair sits 3.58 in lower than the inner pair on purpose: that is how four 10.89 in frames fit across 44 in. The frames mount on the face rather than in a recess.

Impedance. EVL-10 D2: wire for 4 ohms (coils in series, each chamber's pair in series, both cups in parallel), the load most monoblocks are built to deliver full power into; 1 ohm is the other clean option (coils in series, each chamber's pair in parallel, both cups in parallel). EVL-10 D4: wire for 2 ohms (coils in series, each chamber's pair in parallel, both cups in parallel), the load most monoblocks are built to deliver full power into; 8 ohms is the other clean option (coils in series, each chamber's pair in series, both cups in parallel). Work the load out before you buy the amplifier, not after.

Power. Size the amplifier for the set, not one driver: 700 to 1000 W RMS per driver is 2,800 to 4,000 W RMS across all 4. At 4,000 W the charging system is part of the install: alternator output, the big three, and a battery that holds voltage under load.

Skar Audio's Qes and Qms reproduce the printed Qts within 3 percent, so the alignment rests on a self-consistent set. Skar Audio do not publish driver displacement; we deduct an estimated 0.092 per driver, so true net can sit a few hundredths either way.

Polyfill is in as a wall lining in every chamber. Do not add more: it makes the box act larger and walks Qtc off 0.68.

Before you order

Questions

Does this fit the Skar Audio EVL-10, and its coil versions?

Yes. Each opening is cut to 9.400 in for the 10.89 in frame, and the 7.16 in deep motor clears the raked rear panel with 0.75 in to spare. Both coil versions share the frame, cutout and mounting depth; the alignment table lists each.

Run four matched drivers, same model and same coil, so every chamber sees the alignment on this page.

Why 0.732 cubic feet per driver, and what alignment does it target?

On Skar Audio's published Fs 44.0 Hz, Qts 0.590 and Vas 6.8 liters, 0.732 cubic feet per driver gives Qtc 0.680, system resonance 50.7 Hz and half power 52.8 Hz.

The 7.16 in deep motor sets the shallowest the wedge can be, and that smallest box is still more air than flat wants, so it lands below 0.707: tighter and more damped, trading a little extension for control.

What amplifier power should I run, and how should I wire it?

Skar Audio rates the EVL-10 at 1000 watts RMS per driver. Recommended amplifier: 700 to 1000 W RMS per driver, 2,800 to 4,000 W RMS for the full set of 4.

Each EVL-10 D2 has two 2 ohm voice coils, 4 ohms in series or 1 ohm in parallel. Wire every driver's coils in series. With the two drivers in each chamber in parallel and the two cups in parallel, the four present 1 ohm to a mono amplifier. With the two drivers in each chamber in series and the two cups in parallel, they present 4 ohms. Use the lower load only on an amplifier rated stable there. Each EVL-10 D4 has two 4 ohm voice coils, 8 ohms in series or 2 ohms in parallel. Wire every driver's coils in series. With the two drivers in each chamber in parallel and the two cups in parallel, the four present 2 ohms to a mono amplifier. With the two drivers in each chamber in series and the two cups in parallel, they present 8 ohms. Use the lower load only on an amplifier rated stable there.

Will it fit my SUV?

It is 44 inches wide, 17 tall and 15.11 deep at the base, tapering to 8.93 at the top. Measure between the rear wheel wells, the floor depth with the seat upright, and the height under your cargo cover.

The raked face goes against the seat back and the woofers fire toward the liftgate.

Why two drivers per chamber instead of four chambers?

Four chambers would need three dividers, and on a 44 inch face that space is needed for the woofers. Two matched drivers in one sealed chamber move together and see the same pressure, so each behaves as if it had half the chamber to itself: 0.732 cubic feet per driver here.

It also gives two terminal cups, one per pair, which keeps the wiring to the amplifier simple.

What is the expected low-frequency extension?

Anechoic F3 is 52.8 Hz per driver with system resonance at 50.7 Hz.

Those figures exclude cabin gain. An SUV cabin adds real output below about 50 Hz, so in-vehicle response runs deeper than the numbers above.

Do I need to add polyfill or damping?

No. Polyfill is already installed as a light wall lining in every chamber, and the quantity is chosen so it does not change the acoustic volume.

Do not add more. Packing a sealed box makes it behave as though it were larger, which moves the alignment away from 0.732 cubic feet per driver.

Are the drivers included?

No. This is an enclosure only. You receive the cabinet finished in plush black carpet with the gloss black acrylic baffle insert, two side-mounted pre-wired terminal cups, the polyfill lining in place, threaded inserts and stainless machine screws.

Bring four matched Skar Audio EVL-10 drivers. The cabinet is cut direct fit to them, not a general purpose 10 inch box.

Same series, same size

Other Performance Optimized models