Performance Optimized Wedge Wide Sealed Dual 10" Enclosure Arc Audio Black Series 10 · Dual 10" Sealed enclosure

Yes, both coils: they share the 10.5 in frame, the 9.1875 in cutout and the 5.6875 in mounting depth, and the motor clears the cabinet with 0.75 in to spare. One cabinet serves both coils: the Black Series 10 D2 reads Qtc 0.663 with half power at 55.4 Hz, and the D4 reads Qtc 0.737 at 48.1 Hz. Run two of the same coil so the chambers match.

Any other 10, no. The airspace is worked out from the Black Series 10's own Qts and Vas, and a different woofer that happened to drop into the hole would not see the alignment printed on this page.

1.01 cubic feet is what the 41 by 16 face gives each driver at the shallowest depth the 5.6875 inch motor allows, more air than the D2 needs for 0.707, so it lands on the dry side. On the D2 figures (Fs 40.6 Hz, Qts 0.52, Vas 18.0 liters) that is Qtc 0.663 with half power at 55.4 Hz. Below Qtc 0.707 the rolloff starts early and gently and F3 sits above fc: a dry, tightly damped box.

The face is fixed at 41 by 16 for the whole wide dual line, so depth is the only free dimension. One cabinet serves both coils: the Black Series 10 D2 reads Qtc 0.663 with half power at 55.4 Hz, and the D4 reads Qtc 0.737 at 48.1 Hz.

The Black Series 10 is rated at 400 watts RMS per driver, so target 280 to 400 watts RMS per driver at the final load.

A pair of Black Series 10 D2 drivers can land on 0.5 ohm with all four coils in parallel, 2 ohms as series pairs in parallel, or 8 ohms all in series. A pair of Black Series 10 D4 drivers can land on 1 ohm with all four coils in parallel, 4 ohms as series pairs in parallel, or 16 ohms all in series. Anything under 1 ohm, and many amplifiers at 1 ohm, is outside what the amplifier is built for; series wiring is the safe default. Confirm your amplifier's minimum stable impedance first.

41 inches across lets two 10 inch drivers sit side by side while the cabinet stays 12.76 inches deep at the base, so it spans a cargo floor instead of eating into it. The back panel rakes 20 degrees to sit flush against the rear seat.

The cargo area acts as an acoustic extension for the sealed box, and the cabin adds real output below 50 Hz, so in-vehicle response runs deeper than the anechoic 55.4 Hz on this page.

Two drivers sharing one sealed volume load each other: each driver's compression stroke becomes the pressure the other works against, which blurs the alignment either would have alone. A bonded full-height 3/4 inch divider gives each driver its own 1.01 cubic feet and its own polyfill.

It also means a failure in one driver does not unload the other, and the alignment on this page is the alignment in each chamber, not an average across a shared box.

Anechoic F3 is 55.4 Hz per chamber on the D2 and 48.1 Hz on the D4. Below Qtc 0.707 the rolloff starts early and gently and F3 sits above fc: a dry, tightly damped box.

Those figures exclude cabin gain. In a vehicle the cabin's transfer function adds real output below 50 Hz, so in-vehicle response runs deeper than the numbers above.

No. Polyfill is already installed in both chambers as a light wall lining to control internal reflections, and the quantity is chosen so it does not change the acoustic volume.

Do not add more. Packing a sealed box with fill makes it behave as though it were larger, which walks the alignment away from the 1.01 cubic feet per chamber this cabinet was built to.

No drivers. This is an enclosure only. You receive the cabinet finished in plush black carpet with the gloss black acrylic baffle insert, one side-mounted pre-wired terminal cup to both positions, the polyfill lining already in place, and a threaded insert kit with stainless machine screws.

The inserts ship loose on purpose: Arc Audio prints no bolt circle for the Black Series 10, so you set each driver in its recess, mark its holes, drill and press the inserts. The pair of Arc Audio Black Series 10 is purchased separately.