Performance Optimized · Datasheet
Performance Optimized Wedge Wide Sealed Quad 10" Enclosure PowerBass M-1004 · Quad 10" Sealed enclosure
- Net volume
- 0.502 cu ft per driver, 2.01 cu ft total, after the divider and PowerBass's published 0.074 cu ft displacement per driver
- Max mounting depth
- 5.16 in required; 0.75 in clearance above the motor against the raked rear panel
- External dimensions
- 44 in W × 17 in at the seat face H × 12.40 in at the base D
- Front baffle
- 1.5 in double baffle, frames face mounted
- Best For: Quad PowerBass M-1004 SUV Cargo-Floor Builds
- Net Volume: 0.502 cu ft per Driver (2.01 cu ft Net Total)
- Driver Match: Four PowerBass M-1004 (SVC), matched
- Construction: 2 Chambers | 44" Wide Wedge | V-Groove/Dado | Double 1.5" Baffle | 2 Terminal Cups
Spec of record
Technical specifications
| Specification | Value |
|---|---|
| Series | Proline X Performance Optimized Wedge Wide |
| Compatible Driver | PowerBass M-1004, quantity 4, matched. Direct fit |
| Configuration | Quad 10 inch sealed wedge, 2 chambers, 2 drivers per chamber |
| Mounting Position | SUV cargo floor, raked face against the rear seat back |
| Firing Direction | Rearward toward the liftgate. Not a down fire design |
| External Width | 44 in |
| External Height | 17 in at the seat face |
| External Depth | 12.40 in at the base, tapering to 6.21 in at the top |
| Internal Volume, Gross | 2.35 cu ft total |
| Internal Volume, Net Acoustic | 0.502 cu ft per driver, 2.01 cu ft total, after the divider and PowerBass's published 0.074 cu ft displacement per driver |
| Driver Mounting Depth | 5.16 in required; 0.75 in clearance above the motor against the raked rear panel |
| Alignment Per Driver | M-1004 Qtc 0.681, fc 62.2 Hz, F3 64.7 Hz anechoic |
| Woofer Openings | 4 at 9.059 in |
| Woofer Layout | One row across the face |
| Frame Outer Diameter | 10.083 in |
| Fs / Qts / Qes / Qms | 35.0 Hz / 0.383 / 0.423 / 4.050 |
| Vas / Sd / Xmax | 30.8 L / 330 cm2 / 9 mm |
| Driver Power Handling | 325 W RMS per driver, 1300 W RMS for the set of 4 (thermal rating) |
| Recommended Amplifier | 160-230 W RMS per driver, 640-920 W RMS for the full set |
| Parameter Source | PowerBass published specifications |
| Material | Langboard Elite MDF |
| Construction | CNC cut, V-groove and dado joinery |
| Panel Thickness | 0.75 in |
| Front Baffle | 1.5 in double baffle, frames face mounted |
| Internal Bracing | One full-height 3/4 in divider |
| Driver Mounting | Threaded inserts, stainless machine screws included |
| Terminal Cups | Two Proline X ABS and carbon fiber composite, side mounted, one per chamber, pre wired 12 gauge OFC |
| Acrylic Insert | Gloss black acrylic baffle insert standard |
| Damping | Light polyfill wall lining in every chamber, does not alter acoustic volume |
| Carpet | Plush black |
| Shipping Weight | 69 lb |
| Warranty | 1 Year Limited |
| Built In | Tullahoma, Tennessee |
Modelled response
Performance in this enclosure
00Sizing the amplifier
Every wattage on this panel is per driver. This cabinet holds four, so the amplifier feeds all four at once.
01Is it a sealed driver?
Efficiency bandwidth product places the motor before anything else is decided.
02What the box does to it
0.502 cu ft against a 30.8 L Vas.
03The watts that reach Xmax (in this enclosure)
Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 9.0 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.
| Param | Value | Unit | Note |
|---|---|---|---|
| Fs | 35.00 | Hz | free-air resonance |
| Qts | 0.383 | SVC | |
| Vas | 30.75 | L | equivalent compliance |
| Sd | 330.1 | cm² | effective piston area |
| Xmax | 9 | mm | one-way linear travel |
| Pe | 325 | W | continuous RMS |
| SPL | 86.8 | dB | 1 W / 1 m, derived from T/S |
Driver parameters as published by PowerBass M-1004 published specifications. Curves computed against this enclosure’s actual net airspace.
From the shop floor
Installer's take
Start with the size. 0.502 cubic feet per driver puts the M-1004 at Qtc 0.681, resonance 62.2 Hz, half power 64.7 Hz anechoic. The 5.16 in deep motor sets the shallowest the wedge can be, and that smallest box is still more air than flat wants, so it lands below 0.707: tighter and more damped, trading a little extension for control.
Measure the base depth, not the top. This cabinet is 12.40 in deep where it meets the floor, 6.21 at the top, 44 wide and 17 tall. In an SUV the 44 has to clear between the rear wheel wells at floor height, the base depth is measured from the seat back with the seat upright and latched, and the 17 has to clear the cargo cover.
The two terminal cups are on the side panels, one per chamber, so they sit close to the wheel wells. Land the speaker wire on both before the box slides into its final spot, with slack to pull it forward again.
Two drivers share each chamber, so they have to match: same model, same coil, wired in phase. One driver reversed in a shared chamber pushes against its partner and the pair cancels instead of adding. Check polarity at each cup with a battery tap before the box goes in. The frames mount on the face rather than in a recess.
The load depends on which coil version you run, so settle the coil before you buy the amplifier; the wiring section lists the clean loads for each version.
Power. Size the amplifier for the set, not one driver: 160 to 230 W RMS per driver is 640 to 920 W RMS across all 4. On this driver travel sets the top, not heat: Xmax arrives at 234 W per driver with a 25 Hz subsonic, under the 325 W rating. Set the 25 Hz subsonic to use the top of that range; without it keep each driver under 196 W.
PowerBass's Qes and Qms reproduce the printed Qts within 3 percent, so the alignment rests on a self-consistent set.
Polyfill is in as a wall lining in every chamber. Do not add more: it makes the box act larger and walks Qtc off 0.68.
Before you order
Questions
Does this fit the PowerBass M-1004, and its coil versions?
Yes. Each opening is cut to 9.059 in for the 10.083 in frame, and the 5.16 in deep motor clears the raked rear panel with 0.75 in to spare. Coil versions of the PowerBass M-1004 share the frame, cutout and mounting depth, so any of them drops in. The alignment on this page is computed on the M-1004 parameters.
Run four matched drivers, same model and same coil, so every chamber sees the alignment on this page.
Why 0.502 cubic feet per driver, and what alignment does it target?
On PowerBass's published Fs 35.0 Hz, Qts 0.383 and Vas 30.8 liters, 0.502 cubic feet per driver gives Qtc 0.681, system resonance 62.2 Hz and half power 64.7 Hz.
The 5.16 in deep motor sets the shallowest the wedge can be, and that smallest box is still more air than flat wants, so it lands below 0.707: tighter and more damped, trading a little extension for control.
What amplifier power should I run, and how should I wire it?
PowerBass rates the M-1004 at 325 watts RMS per driver. Recommended amplifier: 160 to 230 W RMS per driver, 640 to 920 W RMS for the full set of 4. Travel, not heat, sets the top: the cone reaches Xmax at 234 W per driver with a 25 Hz subsonic set, under the 325 W rating. The top of that range needs the 25 Hz subsonic; without it keep each driver under 196 W.
Loads depend on the coil version you run. Dual 4 ohm drivers, coils in series: 2 ohms with each chamber's pair in parallel, 8 ohms with each pair in series. Dual 2 ohm, coils in series: 1 ohm or 4 ohms the same two ways. Single 4 ohm: 1 ohm or 4 ohms. Use the lower load only on an amplifier rated stable there.
Will it fit my SUV?
It is 44 inches wide, 17 tall and 12.40 deep at the base, tapering to 6.21 at the top. Measure between the rear wheel wells, the floor depth with the seat upright, and the height under your cargo cover.
The raked face goes against the seat back and the woofers fire toward the liftgate.
Why two drivers per chamber instead of four chambers?
Four chambers would need three dividers, and on a 44 inch face that space is needed for the woofers. Two matched drivers in one sealed chamber move together and see the same pressure, so each behaves as if it had half the chamber to itself: 0.502 cubic feet per driver here.
It also gives two terminal cups, one per pair, which keeps the wiring to the amplifier simple.
What is the expected low-frequency extension?
Anechoic F3 is 64.7 Hz per driver with system resonance at 62.2 Hz.
Those figures exclude cabin gain. An SUV cabin adds real output below about 50 Hz, so in-vehicle response runs deeper than the numbers above.
Do I need to add polyfill or damping?
No. Polyfill is already installed as a light wall lining in every chamber, and the quantity is chosen so it does not change the acoustic volume.
Do not add more. Packing a sealed box makes it behave as though it were larger, which moves the alignment away from 0.502 cubic feet per driver.
Are the drivers included?
No. This is an enclosure only. You receive the cabinet finished in plush black carpet with the gloss black acrylic baffle insert, two side-mounted pre-wired terminal cups, the polyfill lining in place, threaded inserts and stainless machine screws.
Bring four matched PowerBass M-1004 drivers. The cabinet is cut direct fit to them, not a general purpose 10 inch box.
Same series, same size
Alpine R2-W10
Alpine RSW10
Alpine RSW10
Alpine S2-W10
Arc Audio Black Series 10
Arc Audio SW10
Arc Audio SW10
Audiofrog GB10