Performance Optimized · Datasheet
Performance Optimized Wedge Wide Sealed Quad 10" Enclosure American Bass XO 10 · Quad 10" Sealed enclosure
- Net volume
- 0.834 cu ft per driver, 3.33 cu ft total, after the divider and an estimated 0.062 cu ft displacement per driver
- Max mounting depth
- 5.10 in required; 4.06 in clearance above the motor against the raked rear panel
- External dimensions
- 44 in W × 17 in at the seat face H × 15.89 in at the base D
- Front baffle
- 1.5 in double baffle, frames face mounted
- Best For: Quad American Bass XO 10 SUV Cargo-Floor Builds
- Net Volume: 0.834 cu ft per Driver (3.33 cu ft Net Total)
- Driver Match: Four American Bass XO 10 (Dual 4 Ohm), matched
- Construction: 2 Chambers | 44" Wide Wedge | V-Groove/Dado | Double 1.5" Baffle | 2 Terminal Cups
Spec of record
Technical specifications
| Specification | Value |
|---|---|
| Series | Proline X Performance Optimized Wedge Wide |
| Compatible Driver | American Bass XO 10, quantity 4, matched. Direct fit |
| Configuration | Quad 10 inch sealed wedge, 2 chambers, 2 drivers per chamber |
| Mounting Position | SUV cargo floor, raked face against the rear seat back |
| Firing Direction | Rearward toward the liftgate. Not a down fire design |
| External Width | 44 in |
| External Height | 17 in at the seat face |
| External Depth | 15.89 in at the base, tapering to 9.71 in at the top |
| Internal Volume, Gross | 3.65 cu ft total |
| Internal Volume, Net Acoustic | 0.834 cu ft per driver, 3.33 cu ft total, after the divider and an estimated 0.062 cu ft displacement per driver |
| Driver Mounting Depth | 5.10 in required; 4.06 in clearance above the motor against the raked rear panel |
| Alignment Per Driver | XO 10 D4 Qtc 0.707, fc 50.5 Hz, F3 50.5 Hz anechoic |
| Woofer Openings | 4 at 9.170 in |
| Woofer Layout | Staggered on the height, outer pair low, inner pair high |
| Frame Outer Diameter | 10.617 in |
| Fs / Qts / Qes / Qms | 37.5 Hz / 0.525 / 0.600 / 4.040 |
| Vas / Sd / Xmax | 19.2 L / 330 cm2 / 11 mm |
| Driver Power Handling | 300 W RMS per driver, 1200 W RMS for the set of 4 (thermal rating) |
| Recommended Amplifier | 200-290 W RMS per driver, 800-1,160 W RMS for the full set, at 2 ohms |
| Parameter Source | American Bass published specifications |
| Material | Langboard Elite MDF |
| Construction | CNC cut, V-groove and dado joinery |
| Panel Thickness | 0.75 in |
| Front Baffle | 1.5 in double baffle, frames face mounted |
| Internal Bracing | One full-height 3/4 in divider |
| Driver Mounting | Threaded inserts, stainless machine screws included |
| Terminal Cups | Two Proline X ABS and carbon fiber composite, side mounted, one per chamber, pre wired 12 gauge OFC |
| Acrylic Insert | Gloss black acrylic baffle insert standard |
| Damping | Light polyfill wall lining in every chamber, does not alter acoustic volume |
| Carpet | Plush black |
| Shipping Weight | 79 lb |
| Warranty | 1 Year Limited |
| Built In | Tullahoma, Tennessee |
Modelled response
Performance in this enclosure
00Sizing the amplifier
Every wattage on this panel is per driver. This cabinet holds four, so the amplifier feeds all four at once.
01Is it a sealed driver?
Efficiency bandwidth product places the motor before anything else is decided.
02What the box does to it
0.834 cu ft against a 19.2 L Vas.
03The watts that reach Xmax (in this enclosure)
Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 11.0 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.
| Param | Value | Unit | Note |
|---|---|---|---|
| Fs | 37.50 | Hz | free-air resonance |
| Qts | 0.525 | Dual 4 Ohm | |
| Vas | 19.20 | L | equivalent compliance |
| Sd | 330.0 | cm² | effective piston area |
| Xmax | 11 | mm | one-way linear travel |
| Pe | 300 | W | continuous RMS |
| SPL | 84.1 | dB | 1 W / 1 m, derived from T/S |
Driver parameters as published by American Bass XO 10 D4 published specifications. Curves computed against this enclosure’s actual net airspace.
From the shop floor
Installer's take
Start with the size. 0.834 cubic feet per driver puts the XO 10 at Qtc 0.707, resonance 50.5 Hz, half power 50.5 Hz anechoic: maximally flat, no peak, the lowest F3 a sealed box reaches without a lift. American Bass publish no sealed recommendation for the XO 10, so this is the Butterworth box.
Measure the base depth, not the top. This cabinet is 15.89 in deep where it meets the floor, 9.71 at the top, 44 wide and 17 tall. In an SUV the 44 has to clear between the rear wheel wells at floor height, the base depth is measured from the seat back with the seat upright and latched, and the 17 has to clear the cargo cover.
The two terminal cups are on the side panels, one per chamber, so they sit close to the wheel wells. Land the speaker wire on both before the box slides into its final spot, with slack to pull it forward again.
Two drivers share each chamber, so they have to match: same model, same coil, wired in phase. One driver reversed in a shared chamber pushes against its partner and the pair cancels instead of adding. Check polarity at each cup with a battery tap before the box goes in. The outer pair sits 1.25 in lower than the inner pair on purpose: that is how four 10.617 in frames fit across 44 in. The frames mount on the face rather than in a recess.
Impedance. XO 10 D4: wire for 2 ohms (coils in series, each chamber's pair in parallel, both cups in parallel), the load most monoblocks are built to deliver full power into; 8 ohms is the other clean option (coils in series, each chamber's pair in series, both cups in parallel). Work the load out before you buy the amplifier, not after.
Power. Size the amplifier for the set, not one driver: 200 to 290 W RMS per driver is 800 to 1,160 W RMS across all 4 at 2 ohms. On this driver travel sets the top, not heat: Xmax arrives at 298 W per driver with a 25 Hz subsonic, under the 300 W rating. Set the 25 Hz subsonic to use the top of that range; without it keep each driver under 234 W.
American Bass's Qes and Qms reproduce the printed Qts within 3 percent, so the alignment rests on a self-consistent set. American Bass do not publish driver displacement; we deduct an estimated 0.062 per driver, so true net can sit a few hundredths either way.
Polyfill is in as a wall lining in every chamber. Do not add more: it makes the box act larger and walks Qtc off 0.71.
Before you order
Questions
Does this fit the American Bass XO 10, and its coil versions?
Yes. Each opening is cut to 9.170 in for the 10.617 in frame, and the 5.10 in deep motor clears the raked rear panel with 4.06 in to spare. Coil versions of the American Bass XO 10 share the frame, cutout and mounting depth, so any of them drops in. The alignment on this page is computed on the XO 10 D4 parameters.
Run four matched drivers, same model and same coil, so every chamber sees the alignment on this page.
Why 0.834 cubic feet per driver, and what alignment does it target?
On American Bass's published Fs 37.5 Hz, Qts 0.525 and Vas 19.2 liters, 0.834 cubic feet per driver gives Qtc 0.707, system resonance 50.5 Hz and half power 50.5 Hz.
Qtc 0.707 is maximally flat: the deepest response a sealed box gives without a lift near resonance.
What amplifier power should I run, and how should I wire it?
American Bass rates the XO 10 at 300 watts RMS per driver. Recommended amplifier: 200 to 290 W RMS per driver, 800 to 1,160 W RMS for the full set of 4. Travel, not heat, sets the top: the cone reaches Xmax at 298 W per driver with a 25 Hz subsonic set, under the 300 W rating. The top of that range needs the 25 Hz subsonic; without it keep each driver under 234 W.
Each XO 10 D4 has two 4 ohm voice coils, 8 ohms in series or 2 ohms in parallel. Wire every driver's coils in series. With the two drivers in each chamber in parallel and the two cups in parallel, the four present 2 ohms to a mono amplifier. With the two drivers in each chamber in series and the two cups in parallel, they present 8 ohms. Use the lower load only on an amplifier rated stable there.
Will it fit my SUV?
It is 44 inches wide, 17 tall and 15.89 deep at the base, tapering to 9.71 at the top. Measure between the rear wheel wells, the floor depth with the seat upright, and the height under your cargo cover.
The raked face goes against the seat back and the woofers fire toward the liftgate.
Why two drivers per chamber instead of four chambers?
Four chambers would need three dividers, and on a 44 inch face that space is needed for the woofers. Two matched drivers in one sealed chamber move together and see the same pressure, so each behaves as if it had half the chamber to itself: 0.834 cubic feet per driver here.
It also gives two terminal cups, one per pair, which keeps the wiring to the amplifier simple.
What is the expected low-frequency extension?
Anechoic F3 is 50.5 Hz per driver with system resonance at 50.5 Hz.
Those figures exclude cabin gain. An SUV cabin adds real output below about 50 Hz, so in-vehicle response runs deeper than the numbers above.
Do I need to add polyfill or damping?
No. Polyfill is already installed as a light wall lining in every chamber, and the quantity is chosen so it does not change the acoustic volume.
Do not add more. Packing a sealed box makes it behave as though it were larger, which moves the alignment away from 0.834 cubic feet per driver.
Are the drivers included?
No. This is an enclosure only. You receive the cabinet finished in plush black carpet with the gloss black acrylic baffle insert, two side-mounted pre-wired terminal cups, the polyfill lining in place, threaded inserts and stainless machine screws.
Bring four matched American Bass XO 10 drivers. The cabinet is cut direct fit to them, not a general purpose 10 inch box.
Same series, same size
Alpine R2-W10
Alpine RSW10
Alpine RSW10
Alpine S2-W10
Arc Audio Black Series 10
Arc Audio SW10
Arc Audio SW10
Audiofrog GB10