

Performance Optimized · Datasheet
JL Audio 10TW1 Dual Box: Sealed 10" Down Fire Enclosure Dual 10" Sealed enclosure
- Net volume
- 0.69 Cubic Feet Total / 0.34 Per Chamber
- Max mounting depth
- 4.37 Inches / 111mm
- Cutout
- 9.055 Inches / 230mm
- External dimensions
- 30 Inches W × 6 Inches H × 15 Inches D
- Front baffle
- Down Firing - Driver Fires Toward Floor
- Alignment: 0.34 cu ft net per chamber (0.69 total). 10TW1-2: Qtc 0.932, Fc 59.5 Hz, F3 48.4 Hz. 10TW1-4: Qtc 0.900, Fc 57.2 Hz, F3 47.4 Hz.
- Fitment: Cut for two JL Audio 10TW1 thin-lines, 9.055" cutout, 4.37" mounting depth.
- Footprint: 30" W x 15" D x 6" H in the down fire position.
- Construction: 2 Separate Chambers | V-Groove/Dado | Double 1.5" Baffle, Flush Recess | Milled Magnet Reliefs | Side Terminal Cup
Spec of record
Technical specifications
| Series | Proline X Performance Optimized Down Fire |
|---|---|
| Enclosure Type | Sealed | Dual Chamber | Down Fire Geometry | Floor-Coupled |
| Driver-Specific Fitment | Two JL Audio 10TW1-2 (SVC 2Ω) / 10TW1-4 (SVC 4Ω) |
| Internal Volume (Gross) | 0.78 Cubic Feet |
| Internal Volume (Net After Displacement) | 0.69 Cubic Feet Total / 0.34 Per Chamber |
| JL Audio Recommended Sealed Volume | 0.35 Cubic Feet Per Driver |
| Target System Qtc | 0.932 (-2) / 0.900 (-4) |
| Predicted Fc | 59.5 Hz (-2) / 57.2 Hz (-4) |
| Predicted F3 | 48.4 Hz (-2) / 47.4 Hz (-4) |
| Driver Fs | 41.5 Hz (-2) / 38.1 Hz (-4) |
| Driver Qts | 0.65 (-2) / 0.60 (-4) |
| Driver Vas | 0.364 Cubic Feet / 10.31 Liters (-2); 0.431 Cubic Feet / 12.2 Liters (-4) |
| Driver Displacement | 0.047 Cubic Feet / 1.33 L |
| Driver Power Handling | 300 Watts RMS Continuous |
| Driver Type | JL Audio TW1 Thin-Line | Single Voice Coil |
| Mounting Depth Required | 4.37 Inches / 111mm |
| Cutout Diameter | 9.055 Inches / 230mm |
| Baffle Configuration | Down Firing - Driver Fires Toward Floor |
| Material | Langboard Elite 3/4" MDF |
| Front Baffle Construction | Double-Layer 1.5" MDF | Outer Layer Flush Recess, Driver Mounts To Inner Layer |
| Magnet Relief | 3/8" Deep Milled Relief In Opposite Panel For Motor Clearance |
| Motor Clearance | 0.5 Inch Minimum Behind Magnet |
| Joinery | V-Groove and Dado (CNC-Cut) |
| Corner Profile | Square (Down Fire Series Standard) |
| Construction | ShopSabre CNC / Perimeter Cross-Brace |
| Chamber Divider | Full-Height Bonded 3/4" MDF | Two Fully Separate Chambers |
| External Width | 30 Inches |
| External Depth | 15 Inches |
| External Height | 6 Inches |
| Dimension Reference | All External Dimensions Measured In Down Fire Position |
| Voice Coil Configuration | Single Voice Coil Each | Parallel Through One Cup: 1 Ohm (-2 Pair) or 2 Ohm (-4 Pair) |
| Combined Power Handling | 600 Watts RMS (Pair) |
| Mounting Hardware | 8/32 Threaded Inserts | Two Sets Stainless Steel Machine Screws Included |
| Terminal Cup | One Shared Proline X ABS/Carbon Fiber Composite | Side Mounted | 12g OFC Pre-Wired |
| Damping | Polyfill Pre-Installed In Each Chamber |
| Carpet Finish | Plush Black |
| Bundle Options | Enclosure Only (Bring Your Own Pair Of JL Audio 10TW1) |
| Warranty | 1-Year Limited (Enclosure) |
| Manufactured | Tullahoma, Tennessee, USA |
From the shop floor
Installer's take
Two thin-lines in a 6 inch tall cabinet, each in its own sealed chamber at 0.34 cubic feet net. That is JL's 0.35 recommendation per driver, and it fell out of the geometry rather than being forced.
The height is set by the driver: 4.37 inches, minus the 0.75 inch flush recess, minus the 3/8 inch magnet relief, plus half an inch behind the motor, gives 3.75 inches inside. On our 30 by 15 platform with a full-height divider, each chamber comes out right on JL's number.
Honest tradeoff: at 0.34 net the 10TW1-2 runs Qtc 0.932 and the 10TW1-4 0.900, so there is lift ahead of the rolloff. The single cabinet in this program is the same alignment in a smaller box; this one is the output product, roughly 6 dB more than one driver, 600 watts RMS across the pair.
Wiring needs attention. Both drivers in parallel through the shared cup present 1 ohm with a pair of 10TW1-2, which many amplifiers will not run. A pair of 10TW1-4 presents 2 ohms. Check your amplifier before you power it.
Before you order
Questions
Why does each chamber hold 0.34 cubic feet?
Because that is JL Audio's recommended 0.35 cubic feet sealed volume for the 10TW1, and this cabinet lands on it per driver. The 10TW1's 4.37 inch mounting depth fixes the internal height at 3.75 inches, a 6 inch cabinet. On our 30 by 15 inch platform, split into two chambers by a full-height divider, each driver gets 0.34 net after its own 0.047 cubic feet of displacement, panel thickness and bracing are subtracted.
What does a Qtc of 0.93 mean in practice?
Qtc describes how a sealed system behaves near its corner frequency. The textbook reference is 0.707, maximally flat. At 0.34 net per chamber the 10TW1-2 sits at 0.932 and the 10TW1-4 at 0.900, so each driver runs above that reference.
In practice that means a modest rise in output around 55 to 60 Hz before a 12 dB per octave rolloff, heard as punch rather than boom. Two drivers add roughly 6 dB of output over one in the same alignment, and firing into the floor the rolloff meets rising cabin gain below 60 Hz.
Why two separate chambers instead of one shared volume?
Two drivers sharing one sealed volume interact acoustically: each driver's compression stroke becomes the pressure the other works against, which smears transients and blurs the alignment. A full-height bonded 3/4 inch MDF divider gives each 10TW1 its own 0.34 cubic feet and its own polyfill, so each behaves exactly as calculated.
How do I wire this enclosure?
Both 10TW1 drivers are single voice coils, wired in parallel to one shared side-mounted Proline X terminal cup, pre-wired in 12 gauge OFC.
A pair of 10TW1-4 presents a 2 ohm load. A pair of 10TW1-2 presents 1 ohm, which many amplifiers are not stable into, so confirm your amplifier's rating first. JL Audio rates each driver at 300 watts RMS, 600 watts across the pair.
Where is the terminal cup located on a down fire enclosure?
Side mounted. Every Proline X Performance Optimized enclosure uses a side mounted terminal cup regardless of alignment, whether standard, wedge, or down fire. On this cabinet that keeps the connection fully accessible with the enclosure in its installed position, since the baffle faces the floor. The cup is our Proline X ABS and carbon fiber composite unit, recessed, with stainless hardware, copper ring terminals, and pre-wired 12 gauge OFC.
What is the milled magnet relief and why is it there?
A 3/8 inch deep circular pocket machined into the panel directly behind each driver's magnet. Even with thin-line drivers like the 10TW1, those reliefs are what let the cabinet stand only 6 inches tall.
They guarantee each motor has room to breathe rather than being crowded against a flat panel, while still leaving half an inch of clearance behind each magnet, which is our practical minimum.
How is this enclosure built?
V-groove and dado joinery, CNC-cut on ShopSabre routers from Langboard Elite MDF. Every panel joint is a machined interlocking groove that mechanically locks the panels before adhesive is applied, which keeps the cabinet airtight under sustained pressure cycling.
The front baffle is a double layer at 1.5 inches, two bonded 3/4 inch sheets, with the outer layer machined as a flush recess so the driver bolts to the inner layer. A 3/8 inch relief is milled into the opposite panel behind the magnet. Perimeter cross-bracing and pre-installed polyfill complete the build. Assembled and inspected in Tullahoma, Tennessee.
Are the JL Audio 10TW1 subwoofers included with this enclosure?
No. This listing is for the enclosure only. Bring your own pair of JL Audio 10TW1 subwoofers, in either the 10TW1-2 or 10TW1-4 version. The cutouts, mounting depth and magnet clearance are all cut specifically for this driver.
Same series, same size
Alpine R2-W10
Alpine RSW10
Alpine RSW10
Alpine S2-W10
Ampere Audio AA-2.0 10
Ampere Audio AA-2.0 10
Arc Audio ARC 10
Arc Audio Black Series 10