

Performance Optimized · Datasheet
JL Audio 10TW1 Box: Sealed 10" Down Fire Enclosure Single 10" Sealed enclosure
- Net volume
- 0.35 Cubic Feet
- Max mounting depth
- 4.37 Inches / 111mm
- Cutout
- 9.055 Inches / 230mm
- External dimensions
- 15.625 Inches W × 6 Inches H × 15 Inches D
- Front baffle
- Down Firing - Driver Fires Toward Floor
- Alignment: 0.35 cu ft net, JL Audio's recommended sealed volume. 10TW1-2: Qtc 0.927, Fc 59.2 Hz, F3 48.3 Hz. 10TW1-4: Qtc 0.895, Fc 56.8 Hz, F3 47.3 Hz.
- Fitment: Cut for the JL Audio 10TW1 thin-line, 9.055" cutout, 4.37" mounting depth.
- Footprint: 15.625" W x 15" D x 6" H in the down fire position.
- Construction: V-Groove/Dado | Double 1.5" Baffle, Flush Recess | Milled Magnet Relief | Side Terminal Cup
Spec of record
Technical specifications
| Series | Proline X Performance Optimized Down Fire |
|---|---|
| Enclosure Type | Sealed | Down Fire Geometry | Floor-Coupled |
| Driver-Specific Fitment | JL Audio 10TW1-2 (SVC 2Ω) / 10TW1-4 (SVC 4Ω) |
| Internal Volume (Gross) | 0.40 Cubic Feet |
| Internal Volume (Net After Displacement) | 0.35 Cubic Feet |
| JL Audio Recommended Sealed Volume | 0.35 Cubic Feet (Matched) |
| Target System Qtc | 0.927 (-2) / 0.895 (-4) |
| Predicted Fc | 59.2 Hz (-2) / 56.8 Hz (-4) |
| Predicted F3 | 48.3 Hz (-2) / 47.3 Hz (-4) |
| Driver Fs | 41.5 Hz (-2) / 38.1 Hz (-4) |
| Driver Qts | 0.65 (-2) / 0.60 (-4) |
| Driver Vas | 0.364 Cubic Feet / 10.31 Liters (-2); 0.431 Cubic Feet / 12.2 Liters (-4) |
| Driver Displacement | 0.047 Cubic Feet / 1.33 L |
| Driver Power Handling | 300 Watts RMS Continuous |
| Driver Type | JL Audio TW1 Thin-Line | Single Voice Coil |
| Mounting Depth Required | 4.37 Inches / 111mm |
| Cutout Diameter | 9.055 Inches / 230mm |
| Baffle Configuration | Down Firing - Driver Fires Toward Floor |
| Material | Langboard Elite 3/4" MDF |
| Front Baffle Construction | Double-Layer 1.5" MDF | Outer Layer Flush Recess, Driver Mounts To Inner Layer |
| Magnet Relief | 3/8" Deep Milled Relief In Opposite Panel For Motor Clearance |
| Motor Clearance | 0.5 Inch Minimum Behind Magnet |
| Joinery | V-Groove and Dado (CNC-Cut) |
| Corner Profile | Square (Down Fire Series Standard) |
| Construction | ShopSabre CNC / Perimeter Cross-Brace |
| External Width | 15.625 Inches |
| External Depth | 15 Inches |
| External Height | 6 Inches |
| Dimension Reference | All External Dimensions Measured In Down Fire Position |
| Voice Coil Configuration | Single Voice Coil | 2 Ohm (-2) or 4 Ohm (-4) Nominal |
| Mounting Hardware | 8/32 Threaded Inserts | Stainless Steel Machine Screws Included |
| Terminal Cup | Proline X ABS/Carbon Fiber Composite | Side Mounted | 12g OFC Pre-Wired |
| Damping | Polyfill Pre-Installed |
| Carpet Finish | Plush Black |
| Bundle Options | Enclosure Only (Bring Your Own JL Audio 10TW1) |
| Warranty | 1-Year Limited (Enclosure) |
| Manufactured | Tullahoma, Tennessee, USA |
From the shop floor
Installer's take
This one is built to JL's number, not past it. The 10TW1 recommendation is 0.35 cubic feet sealed, and with the height locked by the driver, width was the only dimension left to solve. 15 and 5/8 inches across lands it on 0.35 net.
Here is the chain. 4.37 inches of driver, minus 0.75 because our outer baffle layer is a flush recess and the driver bolts to the inner layer, minus 0.375 for the milled magnet relief, plus half an inch of clearance behind the motor. That is 3.75 inches inside and a 6 inch cabinet. It is one of the few builds in the Down Fire program that leaves our shared 30 inch platform.
Be clear about what that buys. With a Qts of 0.65, the 10TW1-2 at 0.35 net sits at Qtc 0.927, the 10TW1-4 at 0.895. That is above the 0.707 flat reference, so expect a little lift around 55 to 60 Hz before the rolloff. It reads as punch, and it is what JL tuned this driver to do in a small sealed box.
Single voice coil, 300 watts RMS. The 10TW1-2 shows your amplifier 2 ohms, the 10TW1-4 shows it 4. Set gain carefully: a thin-line motor has less travel in reserve than a W-series.
Before you order
Questions
Why is this cabinet only 15.6 inches wide?
Because that is the width that lands it on JL Audio's recommended 0.35 cubic feet. The 10TW1's 4.37 inch mounting depth fixes the internal height at 3.75 inches, a 6 inch cabinet, and the depth stays at our standard 15 inches. Width is the one dimension left to solve, and 15.625 inches gives 0.35 net after the driver's 0.047 cubic feet of displacement, panel thickness and bracing are subtracted.
The result is a compact down fire cabinet that fits where a full 30 inch box will not: under seats, in narrow cargo floors, and in tight trunks.
What does a Qtc of 0.93 mean in practice?
Qtc describes how a sealed system behaves near its corner frequency. The textbook reference is 0.707, maximally flat. At 0.35 net the 10TW1-2 sits at 0.927 and the 10TW1-4 at 0.895, so this box is above that reference.
In practice that means a modest rise in output around 55 to 60 Hz before a 12 dB per octave rolloff, heard as punch rather than boom. It is the alignment JL Audio designed this driver around in a small sealed enclosure, and firing into the floor the rolloff meets rising cabin gain below 60 Hz.
How does the 10TW1 compare to the TW3 and W3v3 in this same series?
Depth and size. The 10TW1 needs 4.37 inches of mounting depth against 5.93 for the 10W3v3, and it asks for only 0.35 cubic feet sealed, so this is the smallest cabinet of the three. The 10W3v3 is the higher power driver at 500 watts RMS in a full 30 inch cabinet.
The 10TW3 is JL's other thin-line ten, at 3.25 inches. Choose the 10TW1 for the smallest sealed footprint, the TW3 when depth is the tightest constraint, and the W3v3 when you have the room and want the output.
How do I wire this enclosure?
Straightforward, because the 10TW1 is a single voice coil driver. There is no series or parallel decision to make. The enclosure has one side-mounted Proline X terminal cup pre-wired in 12 gauge OFC.
The amplifier sees 2 ohms with the 10TW1-2 or 4 ohms with the 10TW1-4. JL Audio rates the driver at 300 watts RMS continuous. Confirm your amplifier is comfortable at that load before setting gain.
Where is the terminal cup located on a down fire enclosure?
Side mounted. Every Proline X Performance Optimized enclosure uses a side mounted terminal cup regardless of alignment, whether standard, wedge, or down fire. On this cabinet that keeps the connection fully accessible with the enclosure in its installed position, since the baffle faces the floor. The cup is our Proline X ABS and carbon fiber composite unit, recessed, with stainless hardware, copper ring terminals, and pre-wired 12 gauge OFC.
What is the milled magnet relief and why is it there?
A 3/8 inch deep circular pocket machined into the panel directly behind the driver's magnet. Even on a thin-line driver like the 10TW1, that relief is what lets the cabinet stand only 6 inches tall.
It guarantees the motor has room to breathe rather than being crowded against a flat panel, while still leaving half an inch of clearance behind the magnet, which is our practical minimum.
How is this enclosure built?
V-groove and dado joinery, CNC-cut on ShopSabre routers from Langboard Elite MDF. Every panel joint is a machined interlocking groove that mechanically locks the panels before adhesive is applied, which keeps the cabinet airtight under sustained pressure cycling.
The front baffle is a double layer at 1.5 inches, two bonded 3/4 inch sheets, with the outer layer machined as a flush recess so the driver bolts to the inner layer. A 3/8 inch relief is milled into the opposite panel behind the magnet. Perimeter cross-bracing and pre-installed polyfill complete the build. Assembled and inspected in Tullahoma, Tennessee.
Is the JL Audio 10TW1 subwoofer included with this enclosure?
No. This listing is for the enclosure only. Bring your own JL Audio 10TW1, in either the 10TW1-2 or 10TW1-4 version. The cutout, mounting depth and magnet clearance are all cut specifically for this driver.
Same series, same size
Alpine R2-W10
Alpine RSW10
Alpine RSW10
Alpine S2-W10
Ampere Audio AA-2.0 10
Ampere Audio AA-2.0 10
Arc Audio ARC 10
Arc Audio Black Series 10