Shop

Performance Optimized · Datasheet

Dayton Audio Max-X MX15-22 Box: Sealed 15" Down Fire Wide Enclosure Single 15" Sealed enclosure

Net volume
2.49 cu ft after the brace and the driver displacement
Max mounting depth
9.13 in required, 0.81 in clearance above the motor
External dimensions
38.00 in W × 10.6875 in in the down fire position H × 17.00 in D
Front baffle
1.5 in double baffle, outer layer machined as a flush recess
Buy at Audio IntensityFactory-direct, ships from Tullahoma
Dayton Audio Max-X MX15-22Buy at Audio Intensity
  • Alignment: 2.49 cu ft net, Qtc 0.70, F3 38.4 Hz; height set by the motor, not the airspace
  • Driver: Dayton Audio Max-X MX15-22 (dual 2 ohm), 800 W RMS, 19 mm Xmax, 9.13 in mounting depth
  • Standoffs: Included, 1.75 in, shipped uninstalled. Installed height near 12.44 in
  • Cabinet: 38"W x 17"D x 10.6875"H in down fire position, excludes standoffs, square corners

Spec of record

Technical specifications

SpecificationValue
SeriesProline X Performance Optimized Down Fire Wide
Compatible DriverDayton Audio Max-X MX15-22 (dual 2 ohm), quantity 1. Direct fit
ConfigurationSingle 15 inch, sealed down fire
Mounting PositionTrunk or cargo floor, baffle facing down on standoffs
Firing DirectionDownward. Feet ship uninstalled, so front or up firing is also possible
External Width38.00 in
External Depth17.00 in
External Height10.6875 in in the down fire position, excludes standoffs
Installed Height12.44 in including the 1.75 in standoff
Internal Volume, Gross2.69 cu ft
Internal Volume, Net Acoustic2.49 cu ft after the brace and the driver displacement
Height Set ByDriver clearance: the 9.13 in motor, not the airspace
Driver Mounting Depth9.13 in required, 0.81 in clearance above the motor
Alignment, MX15-22 (dual 2 ohm)Qtc 0.700, fc 38.0 Hz, F3 38.4 Hz anechoic
Woofer Opening14.01 in, cut for Dayton's frame
Frame Outer Diameter15.42 in
Bolt Circle14.65 in, Dayton spec; threaded inserts pre-installed
Driver Displacement0.180 cu ft, estimated; Dayton publishes none
MX15-22 (dual 2 ohm) Fs / Qts / Qes / Qms / Vas21.7 Hz / 0.4 / 0.46 / 4.27 / 146 L
Driver Sd820 cm2, Dayton spec
Xmax19 mm, one-way, as Dayton publish it
Driver Power Handling800 W RMS
Wiring OptionsDayton builds the MX15-22 in one version, dual 2 ohm: two 2 ohm coils, 4 ohms in series or 1 ohm in parallel. Series to 4 ohms is the safe default; run the 1 ohm parallel load only on an amplifier rated 1 ohm stable.
Parameter SourceDayton Audio spec sheet
MaterialLangboard Elite MDF
ConstructionCNC cut, V-groove and dado joinery, square corners
Panel Thickness0.75 in
Front Baffle1.5 in double baffle, outer layer machined as a flush recess
Internal BracingWindowed brace, dadoed to the shell
Driver MountingThreaded inserts pre-installed at Dayton's bolt circle; stainless machine screws included
Terminal CupsOne Proline X ABS and carbon fiber composite, side mounted, pre wired 12 gauge OFC
StandoffsIncluded, 1.75 in, shipped uninstalled
DampingLight polyfill wall lining, does not alter acoustic volume
CarpetPlush black
Shipping Weight57 lb
Warranty1 Year Limited
Built InTullahoma, Tennessee

Modeled response

Performance in this enclosure

Net airspace
2.49
cu ft
System Qtc
0.70
sealed
Half power
38.4
Hz · F3
Xmax at
761
W RMS · no filter
With 25 Hz subsonic
1212
W RMS · +59%
Amplifier
800
W RMS recommended
This enclosure holds 2.49 cu ft net . In it the Dayton Audio MX15-22 runs a system Qtc of 0.70 with half power at 38.4 Hz, and the cone reaches its 19.0 mm travel limit at 761 W, below the driver’s 800 W thermal rating, so travel is what stops you here, not heat. Run a subsonic filter at 25 Hz and that becomes 1212 W — +451 W, or 59 percent more power for the same 19.0 mm of travel.

01Is it a sealed driver?

Efficiency bandwidth product places the motor before anything else is decided.

EBP = Fs ÷ Qes = 47.2
SEALED 0–50 TRANSITION 50–100 PORTED 100–150 0 50 100 150 MX15-22 47.2
MX15-22 · EBP 47.2
EBP under 50 means a motor that wants a sealed load. The MX15-22 sits at 47.2, inside that band, which is why this is a sealed build rather than a ported one.

02What the box does to it

2.49 cu ft against a 146.0 L Vas.

α = Vas ÷ Vb = 2.07  ·  Fc = Fs√(α+1) = 38 Hz  ·  Qtc = 0.70
20 30 50 70 100 150 200 +6 +0 -6 -12 -18 -24 FREQUENCY · Hz LEVEL · dB −3 dB
MX15-22 · Qtc 0.70, Fc 38 Hz, F3 38.4 Hz
The box lifts resonance from 21.7 Hz free-air to 38 Hz and half power lands at 38.4 Hz, anechoic, before any cabin gain. Parameters are Dayton Audio’s own spec sheet, measured with the two 2 ohm coils in series. Driver displacement is not published and is estimated.

03The watts that reach Xmax (in this enclosure)

Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 19.0 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.

PXmax = 761 W unfiltered  →  1212 W with a 25 Hz subsonic
20 30 50 70 100 150 200 0 4 8 12 16 20 24 FREQUENCY · Hz CONE TRAVEL · mm PAST LINEAR TRAVEL · Xmax 19.0 mm 761 W reaches Xmax here
MX15-22 · 761 W, no filterMX15-22 · 1212 W with subsonic at 25 Hz, 24 dB/octXmax 19.0 mm one-way
Every trace touches the limit and no further, because each is drawn at the exact power that puts that coil on 19.0 mm. Unfiltered that is 761 W, reached first at 20 Hz. It sits under the 800 W the driver can take thermally, so the enclosure sets the ceiling, not the voice coil. The dashed traces are the same driver behind a subsonic filter at 25 Hz, 24 dB/oct: stopping the cone wasting travel below the passband lets it take 1212 W before hitting the same 19.0 mm. That is 59 percent more amplifier for the price of one filter setting.
ParamValueUnitNote
Fs21.70Hzfree-air resonance
Qts0.400MX15-22
Vas146.00Lequivalent compliance
Sd819.8cm²effective piston area
Xmax19mmone-way, as Dayton publish it
Pe800Wcontinuous RMS
SPL87.0dB1 W / 1 m, derived from T/S

Driver parameters as published by Dayton Audio spec sheet. Curves computed against this enclosure’s actual net airspace.

From the shop floor

Installer's take

2.49 cubic feet: Qtc 0.700 on the MX15-22 (dual 2 ohm), F3 38.4 Hz.

Measure the installed height, not the cabinet height: 10.6875 tall on its own, 12.44 with the standoffs on the 38 by 17 footprint.

Dayton's spec sheet holds together on every check I run. Displacement is the one figure they do not give, so it is estimated.

Inserts are pressed at Dayton's bolt circle, so the driver bolts straight in. Sealed, so leave the polyfill as it is and run it at 800 watts or under per driver.

Before you order

Questions

Does this fit the Dayton Audio Max-X MX15-22, and will any other 15 inch fit?

The Max-X MX15-22, yes, in its only version, dual 2 ohm. The baffle is cut to 14.01 in for Dayton's 15.42 in frame. The 9.13 inch motor clears the cabinet with 0.81 inch to spare.

Any other 15, no. The airspace is engineered around the Max-X MX15-22's own Qts and Vas, and a different woofer that happened to drop into the hole would not see the alignment printed on this page.

Why 2.49 cubic feet, and what alignment does it target?

2.49 cubic feet net on Dayton's published figures: the MX15-22 (dual 2 ohm) reads Qtc 0.700 with resonance at 38.0 Hz and half power at 38.4 Hz. That is maximally flat: the flattest a sealed box gets, with no lift near resonance and fc and F3 landing together.

The 9.13 inch mounting depth sets the minimum cabinet height here, so the airspace is what the motor allows rather than a free choice.

What amplifier power should I run, and how should I wire it?

Dayton rates the Max-X MX15-22 at 800 watts RMS, so target 560 to 800 watts RMS at the final load.

Dayton builds the MX15-22 in one version, dual 2 ohm: two 2 ohm coils, 4 ohms in series or 1 ohm in parallel. Series to 4 ohms is the safe default; run the 1 ohm parallel load only on an amplifier rated 1 ohm stable. Confirm your amplifier's minimum stable impedance first.

How tall is this once the standoffs are on?

The cabinet is 10.6875 inches tall measured in the down fire position, and that figure excludes the standoffs. The standoffs hold 1.75 inches under the baffle, so plan your space around a finished stack of roughly 12.44 inches.

This is a Down Fire Wide build, 38 inches long by 17 deep, with cabinet height as the variable. This one stands 10.6875 inches tall, the least its 9.13 inch motor allows, where the standard 30 by 15 would need 14.45.

Why is the front baffle double-layered?

The baffle is two bonded 3/4 inch sheets, 1.5 inches through. A single 3/4 inch panel flexes under the pressure a 15 inch woofer puts on it at 800 watts, which smears output and works the driver loose over time; the second layer stiffens the face and gives the mounting hardware twice the material to bite.

The outer layer is machined as a flush recess to Dayton's 15.42 inch frame, so the driver bolts to the inner layer.

What is the expected low-frequency extension?

Anechoic F3 is 38.4 Hz. At Qtc 0.707 F3 and fc coincide and the response rolls off without a lift near resonance.

Those figures exclude cabin gain. In a car the cabin's transfer function adds real output below 50 Hz, so in-vehicle response runs deeper than the numbers above.

Do I need to add polyfill or damping?

No. Polyfill is already installed as a light wall lining to control internal reflections, and the quantity is chosen so it does not change the acoustic volume.

Do not add more. Packing a sealed box with fill makes it behave as though it were larger, which walks the alignment away from the 2.49 cubic feet this cabinet was built to.

Is the driver included, and are the threaded inserts installed?

No driver. This is an enclosure only. You receive the cabinet finished in plush black carpet, one side-mounted pre-wired terminal cup, the polyfill lining already in place, the standoffs, and stainless machine screws, with the threaded inserts already pressed.

The inserts are pressed at the shop on Dayton's published bolt circle for the Max-X MX15-22, so the driver bolts straight in. The Dayton Audio Max-X MX15-22 is purchased separately, and the cabinet is cut direct fit to it, not a general purpose 15 inch box.

Same series, same size

Other Performance Optimized models