

Performance Optimized · Datasheet
Dayton Audio Max-X MX10-22 Dual Box: Sealed 10" Wedge Enclosure Dual 10" Sealed enclosure
- Net volume
- 0.61 cu ft per chamber after the divider and the driver displacement
- Max mounting depth
- 6.27 in required; 0.75 in clearance above the motor against the raked rear panel
- External dimensions
- 26.83 in W × 15 in at the seat face H × 13.17 in at the base D
- Front baffle
- 1.5 in double baffle, outer layer machined as a flush recess
- Best For: Dual Dayton Audio Max-X MX10-22 Trunk-Fit Builds
- Net Volume: 0.61 cu ft per chamber (1.41 cu ft Gross Total)
- Driver Match: Pair of Dayton Audio Max-X MX10-22 (dual 2 ohm), matched
- Construction: Dual Chamber | Rear-Firing Wedge | V-Groove/Dado | Double 1.5" Baffle | 1 Shared Terminal Cup | Inserts Installed
Spec of record
Technical specifications
| Specification | Value |
|---|---|
| Series | Proline X Performance Optimized Wedge |
| Compatible Driver | Dayton Audio Max-X MX10-22 (dual 2 ohm), quantity 2. Direct fit |
| Configuration | Dual 10 inch, two separate chambers, sealed wedge |
| Mounting Position | Trunk or cargo area, tall face against the rear seat back |
| Firing Direction | Rearward into the trunk. Not a down fire design, no feet included |
| External Width | 26.83 in |
| External Height | 15 in at the seat face |
| External Depth | 13.17 in at the base, tapering to 7.71 in at the top |
| Internal Volume, Gross | 1.41 cu ft total |
| Internal Volume, Net Acoustic | 0.61 cu ft per chamber after the divider and the driver displacement |
| Driver Mounting Depth | 6.27 in required; 0.75 in clearance above the motor against the raked rear panel |
| Alignment, MX10-22 (dual 2 ohm) per chamber | Qtc 0.707, fc 50.1 Hz, F3 50.1 Hz anechoic |
| Woofer Opening | 9.05 in, two, cut for Dayton's frame |
| Frame Outer Diameter | 10.33 in |
| Bolt Circle | 9.65 in, Dayton spec; threaded inserts pre-installed |
| Driver Displacement | 0.071 cu ft, estimated; Dayton publishes none |
| MX10-22 (dual 2 ohm) Fs / Qts / Qes / Qms / Vas | 32.6 Hz / 0.46 / 0.53 / 3.59 / 23.7 L |
| Driver Sd | 357 cm2, Dayton spec |
| Xmax | 11.6 mm, one-way, as Dayton publish it |
| Driver Power Handling | 400 W RMS per driver |
| Wiring Options | Dayton builds the MX10-22 in one version, dual 2 ohm, so a pair always matches. Wire each woofer's coils in series and the two woofers in parallel for 2 ohms, or everything in series for 8 ohms. Paralleling every coil lands on 0.5 ohm, below what any amplifier is built for, so do not. |
| Parameter Source | Dayton Audio spec sheet |
| Material | Langboard Elite MDF |
| Construction | CNC cut, V-groove and dado joinery |
| Panel Thickness | 0.75 in |
| Front Baffle | 1.5 in double baffle, outer layer machined as a flush recess |
| Internal Bracing | Full-height 3/4 in divider |
| Driver Mounting | Threaded inserts pre-installed at Dayton's bolt circle; stainless machine screws included |
| Terminal Cups | One Proline X ABS and carbon fiber composite, side mounted, pre wired 12 gauge OFC to both driver positions |
| Acrylic Insert | Gloss black acrylic baffle insert standard |
| Damping | Light polyfill wall lining in both chambers, does not alter acoustic volume |
| Carpet | Plush black |
| Shipping Weight | 44 lb |
| Warranty | 1 Year Limited |
| Built In | Tullahoma, Tennessee |
Modeled response
Performance in this enclosure
01Is it a sealed driver?
Efficiency bandwidth product places the motor before anything else is decided.
02What the box does to it
0.61 cu ft against a 23.7 L Vas.
03The watts that reach Xmax (in this enclosure)
Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 11.6 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.
| Param | Value | Unit | Note |
|---|---|---|---|
| Fs | 32.60 | Hz | free-air resonance |
| Qts | 0.460 | MX10-22 | |
| Vas | 23.70 | L | equivalent compliance |
| Sd | 356.7 | cm² | effective piston area |
| Xmax | 11.6 | mm | one-way, as Dayton publish it |
| Pe | 400 | W | continuous RMS |
| SPL | 83.8 | dB | 1 W / 1 m, derived from T/S |
Driver parameters as published by Dayton Audio spec sheet. Curves computed against this enclosure’s actual net airspace.
From the shop floor
Installer's take
0.61 cubic feet per chamber: Qtc 0.707 on the MX10-22 (dual 2 ohm), F3 50.1 Hz.
The 6.27 inch motor clears the raked back with 0.75 to spare; the airspace sets the rest of the cabinet.
Dayton's spec sheet holds together on every check I run. Displacement is the one figure they do not give, so it is estimated.
Inserts are pressed at Dayton's bolt circle, so the driver bolts straight in. Sealed, so leave the polyfill as it is and run it at 400 watts or under per driver.
Before you order
Questions
Does this fit the Dayton Audio Max-X MX10-22, and will any other 10 inch fit?
The Max-X MX10-22, yes, in its only version, dual 2 ohm. The baffle is cut to 9.05 in for Dayton's 10.33 in frame. The 6.27 inch motor clears the cabinet with 0.75 inch to spare.
Any other 10, no. The airspace is engineered around the Max-X MX10-22's own Qts and Vas, and a different woofer that happened to drop into the hole would not see the alignment printed on this page.
Why 0.61 cubic feet per chamber, and what alignment does it target?
0.61 cubic feet net per chamber on Dayton's published figures: the MX10-22 (dual 2 ohm) reads Qtc 0.707 with resonance at 50.1 Hz and half power at 50.1 Hz. That is maximally flat: the flattest a sealed box gets, with no lift near resonance and fc and F3 landing together.
Cabinet gain in a vehicle lifts the bottom end further, so in the car this reads deeper than the anechoic figures.
What amplifier power should I run, and how should I wire it?
Dayton rates the Max-X MX10-22 at 400 watts RMS per driver, so target 280 to 400 watts RMS per driver at the final load.
Dayton builds the MX10-22 in one version, dual 2 ohm, so a pair always matches. Wire each woofer's coils in series and the two woofers in parallel for 2 ohms, or everything in series for 8 ohms. Paralleling every coil lands on 0.5 ohm, below what any amplifier is built for, so do not. Confirm your amplifier's minimum stable impedance first.
Why the wedge angle, and why rear-firing into the trunk?
The seat-side face carries a 20 degree rake that matches the lean of a factory rear seat back, so the cabinet sits flush against it and the cargo space in front stays usable. The baffle is the vertical trunk-lid-side face, so the drivers fire rearward into the trunk cavity.
The trunk acts as an acoustic extension for the sealed box, and the cabin adds real output below 50 Hz, so in-vehicle response runs deeper than the anechoic 50.1 Hz on this page.
Why two separate chambers instead of one shared volume?
Two drivers sharing one sealed volume load each other: each driver's compression stroke becomes the pressure the other works against, which blurs the alignment either would have alone. A bonded full-height 3/4 inch divider gives each driver its own 0.61 cubic feet and its own polyfill.
It also means a failure in one driver does not unload the other, and the alignment on this page is the alignment in each chamber, not an average across a shared box.
What is the expected low-frequency extension?
Anechoic F3 is 50.1 Hz per chamber. At Qtc 0.707 F3 and fc coincide and the response rolls off without a lift near resonance.
Those figures exclude cabin gain. In a car the cabin's transfer function adds real output below 50 Hz, so in-vehicle response runs deeper than the numbers above.
Do I need to add polyfill or damping?
No. Polyfill is already installed in both chambers as a light wall lining to control internal reflections, and the quantity is chosen so it does not change the acoustic volume.
Do not add more. Packing a sealed box with fill makes it behave as though it were larger, which walks the alignment away from the 0.61 cubic feet per chamber this cabinet was built to.
Is the driver included, and are the threaded inserts installed?
No driver. This is an enclosure only. You receive the cabinet finished in plush black carpet with the gloss black acrylic baffle insert, one side-mounted pre-wired terminal cup to both positions, the polyfill lining already in place, and stainless machine screws, with the threaded inserts already pressed.
The inserts are pressed at the shop on Dayton's published bolt circle for the Max-X MX10-22, so the driver bolts straight in. The pair of Dayton Audio Max-X MX10-22 is purchased separately, and the cabinet is cut direct fit to it, not a general purpose 10 inch box.
Same series, same size
Alpine R2-W10
Alpine RSW10
Alpine RSW10
Alpine S2-W10
Ampere Audio AA-2.0 10
Ampere Audio AA-2.0 10
Arc Audio ARC 10
Arc Audio Black Series 10