Shop
Proline X PO 10D-P W SPC10 dual ported wedge, front baffle with gloss black insert, 32 by 15 inches.
Proline X PO 10D-P W SPC10 dual ported wedge, side profile with the port mouth, 14.3 inch base, 15 inches tall.

Performance Optimized · Datasheet

AudioControl Space SPC-10 Dual Box: Ported 10" Shallow Wedge Enclosure Dual 10" Ported enclosure

Net volume
1.43 cu ft, one shared chamber (0.72 per driver)
Tuning
35.5 Hz
External dimensions
32.00" W x 15" H
Front baffle
1.5 in double baffle
Buy at Audio IntensityFactory-direct, ships from Tullahoma
AudioControl Space SPC-10Buy at Audio Intensity
  • Alignment: 1.43 cu ft net shared, vented at 35.5 Hz, F3 39.5 Hz
  • Drivers: Pair of AudioControl Space SPC-10 (SPC-10S2 or SPC-10S4), 400 W RMS each
  • Port: Triangular side slot, 23.0 sq in
  • Cabinet: 32.00" W x 15" H x 8.88/14.33" D

Spec of record

Technical specifications

SeriesProline X Performance Optimized Ported Wedge
Compatible DriverAudioControl SPC-10S2 (single 2 ohm) or SPC-10S4 (single 4 ohm), quantity 2. Direct fit
External Dimensions32.00" W x 15" H, 14.33" D at the base tapering to 8.88" at the top
Internal Volume, Net1.43 cu ft, one shared chamber (0.72 per driver)
Tuning35.5 Hz
PortTriangular side slot, 23.0 sq in, 26.8 in path
AlignmentF3 39.5 Hz anechoic, ripple 0.1 dB
Driver Openings9.13 in cutout, 10.39 in recess, x2 at 8.625 / 23.375 in
Driver MountingThreaded insert kit and stainless machine screws included; AudioControl publishes no bolt circle
Driver Displacement0.045 cu ft each, AudioControl spec
Parameter SourceAudioControl user manual
Motor Clearance2.82 in to the port panel
Bracing2 windowed C braces
MaterialLangboard Elite MDF, V-groove and dado joinery
Front Baffle1.5 in double baffle
Terminal CupOne, side mounted, pre wired 12 gauge OFC to both drivers
Acrylic InsertGloss black acrylic baffle insert standard
DampingNone, ships dry
CarpetPlush black
Shipping Weight57 lb
Warranty1 Year Limited
Built InTullahoma, Tennessee

Modelled response

Performance in this enclosure

Net airspace
1.43
cu ft
Tuning
35.5
Hz · Fb
Half power
39.5
Hz · F3, anechoic
Xmax at
1378
W RMS · 28 Hz subsonic
With NO filter
202
W RMS · unfiltered
Port
13.7
m/s at the mouth

01Is this driver right for a ported box?

Efficiency bandwidth product places the motor before anything else is decided.

EBP = Fs ÷ Qes = 76.8
SEALED 0–50 TRANSITION 50–100 PORTED 100–150 0 50 100 150 EBP 76.8
AudioControl SPC-10S2 · EBP 76.8
Between 50 and 100 a driver takes either load, and the choice becomes one of priorities rather than of physics. The AudioControl SPC-10S2 reads 76.8. Ported buys output and low-end reach around tuning; sealed buys a shallower rolloff below it. This cabinet takes the first trade.

02What the box does to it

1.43 cu ft net against a 47.3 L Vas, vented at 35.5 Hz.

Fb = 35.5 Hz  ·  F3 = 39.5 Hz  ·  passband ripple 0.07 dB
20 30 50 70 100 150 200 +4 0 −4 −8 −12 −16 −20 −24 −28 −32 −36 FREQUENCY · Hz LEVEL · dB −3 dB Fb 35.5
AudioControl SPC-10S2 · Fb 35.5 Hz, F3 39.5 Hz
Anechoic, before any cabin gain, with the 28 Hz subsonic filter already applied. The vent takes over below 36 Hz and the cone stops doing the work there, which is what holds travel down at the bottom of the passband.

03Ported vs Sealed

No sealed comparison is shown for this driver.

A ported-versus-sealed chart is only worth reading against a sealed box someone would actually build: the one we make for the driver, or the one its maker recommends. Neither exists for the AudioControl SPC-10S2 — we do not build a sealed enclosure for it and AudioControl publish no sealed volume for it — so rather than compare this cabinet against itself stuffed and sealed, a box no one would build, the comparison is left out.

04The watts that reach Xmax (in this enclosure)

Travel scales with the square root of power, so there is one wattage that puts both cones exactly on AudioControl's published 9.0 mm. The two traces are the same cabinet with the subsonic filter switched on and switched off. Every power figure in this section is for the pair, split evenly.

PXmax = 1378 W with a 28 Hz subsonic  ·  202 W with none  →  the filter is worth 6.8×
20 30 50 70 100 150 200 0 4 8 FREQUENCY · Hz CONE TRAVEL · mm PAST LINEAR TRAVEL · Xmax 9.0 mm 1378 W reaches Xmax here
1378 W · subsonic at 28 Hz, 24 dB/oct202 W · no subsonic filterXmax 9.0 mm one-way, published
Each trace touches the limit and no further, because each is drawn at the exact power that puts the cone on 9.0 mm. With a 28 Hz subsonic that takes 1378 W, reached first at 26 Hz. Take the filter away and the same cabinet reaches 9.0 mm on 202 W — the filter is worth 6.8× the safe power. A vent unloads the cone below tuning, so there is nothing holding it once the box stops loading: on a sealed build a subsonic filter is an improvement, here it is required equipment. The unfiltered trace is still rising where this chart stops at 20 Hz, so treat 202 W as a bound rather than a floor. Every wattage on this page is a MECHANICAL limit, not an electrical one. It is the power at which the cone runs out of linear travel in this cabinet, and nothing more. What the voice coil can dissipate as heat is a separate ceiling set by the driver, not by the box — AudioControl rate this one at 800 W RMS, and that is the number that binds first here: heat stops you before travel does, so treat 800 W as the ceiling and the travel figures above as headroom. Final wired impedance, amplifier output and how long you hold the level are all electrical questions this graph does not answer.

From the shop floor

Installer's take

Two SPC10s on 1.43 cubic feet at 35.5 Hz, one shared chamber, 39.5 Hz anechoic. The mouth runs about 14 m/s with both at 400 watts.

Drivers sit at 8.625 and 23.375 from the mouth side, braces between them, each motor inside a brace window.

AudioControl prints no bolt circle, so the baffle ships undrilled with a threaded insert kit and stainless machine screws: set each driver in its recess, mark its holes, drill and press the inserts. Ships dry, subsonic near 30 Hz.

Before you order

Questions

Why is this enclosure tuned to 35.5 Hz?

This cabinet gives the pair 1.43 cubic feet in one shared chamber, 0.72 per driver, vented at 35.5 Hz through a 23.0 square inch triangular port, and reaches 39.5 Hz anechoic in a 32 by 15 inch dual wedge. The port runs 21.0 m/s in the channel and 13.7 at the flared mouth with both drivers at 400 watts, and each cone peaks at 6.8 of its 9 mm. Passband ripple is 0.1 dB. Our sealed dual wedge (PO 10D-S W SPC10) holds 0.60 cubic feet per chamber at Qtc 0.67 with half power at 61 Hz; this ported box reaches deeper.

Why the 20 degree wedge, and why rear-firing?

The rake on the back matches a factory rear seat so the cabinet sits flush and the trunk floor in front stays usable; the baffle is vertical and fires rearward, using the trunk as an acoustic extension.

Do I need a subsonic filter?

Yes. Below 35.5 Hz the port no longer controls the cones; set the filter near 30 Hz.

How much power can I run, and at what impedance?

AudioControl rates the SPC-10 at 400 watts RMS per driver, 800 across the pair; aim for 280 to 400 per driver. A pair of SPC-10S2 (one 2 ohm coil each) is 1 ohms in parallel or 4 ohms in series. A pair of SPC-10S4 (one 4 ohm coil each) is 2 ohms in parallel or 8 ohms in series.

Would a sealed box be better for me?

Our sealed dual wedge for the SPC10 holds 0.60 cubic feet per chamber at Qtc 0.67, half power 61 Hz: tighter and smaller. This ported box reaches 39.5 Hz on the same pair.

How does the side port work?

The port is a triangular slot along the back, 26.8 inches of path, exiting through the side panel with a rounded mouth so the air leaves without a sharp edge to chuff on.

Does this enclosure ship with polyfill?

No, and do not add any: fill in a ported box detunes it.

Are the SPC10s included?

No. This is an enclosure only, for a pair you supply. It fits both AudioControl versions, the SPC-10S2 (single 2 ohm) and the SPC-10S4 (single 4 ohm); the pair is tuned on the SPC-10S2 and the SPC-10S4 was run through the same cabinet: F3 40.0 Hz, ripple 0.1 dB, each cone 6.7 of its 9 mm at 400 W. You receive the cabinet in plush black carpet with the gloss black acrylic insert, the side-mounted pre-wired terminal cup and a threaded insert kit with stainless machine screws.

Same series, same size

Other Performance Optimized models