Performance Optimized Wedge Sealed 12" Enclosure Audiomobile Encore 4412 · Single 12" Sealed enclosure

The Encore 4412, yes: the baffle is cut to Audiomobile's 11.00 inch cutout, the recess to its 12.65 inch frame, and the raked rear panel clears the 4.9 inch motor with 0.75 inch to spare. The Encore ships in one version, dual 4 ohm, so there is no coil variant to choose.

Any other 12, no. The airspace is engineered around the Encore 4412's 0.518 Qts and 30.12 liters of Vas, and a different woofer that happened to drop into the hole would not see the alignment printed on this page.

0.90 cubic feet sits inside Audiomobile's 0.7 to 1.25 cubic feet sealed range and above the 0.8 cubic foot minimum on its sheet. Computed from Audiomobile's published Fs 32.0 Hz, Qts 0.518 and Vas 30.12 liters it gives system Qtc 0.765, resonance 47.3 Hz and an anechoic half-power point of 44.0 Hz.

The maximally flat Butterworth box for this driver would be 1.23 cubic feet. This cabinet is built a little smaller on purpose: Qtc 0.77 adds at most 0.1 dB of punch around resonance without giving up extension, and keeps the wedge to a trunk-friendly 24.01 inches wide.

Audiomobile rates the Encore 4412 at 1000 watts RMS and 2000 watts maximum, so target 700 to 1000 watts RMS at the final impedance. Each driver carries two 4 ohm coils: parallel for 2 ohms (1.68 ohms DC, the way Audiomobile measured it), series for 8 ohms.

A 2 ohm load is within most monoblocks' rating, but confirm your amplifier's minimum stable impedance before you wire it; 8 ohms in series is the safe answer on any amplifier at the cost of output.

The seat-side face carries a 20 degree rake that matches the lean of a factory rear seat back, so the cabinet sits flush against it and the cargo space in front stays usable. The baffle is the vertical trunk-lid-side face, so the driver fires rearward into the trunk cavity.

The trunk acts as an acoustic extension for the sealed box, and the cabin's transfer function adds real output below 50 Hz, so in-vehicle response runs deeper than the anechoic 44.0 Hz on this page.

The baffle is two bonded 3/4 inch sheets, 1.5 inches through. A subwoofer pushes as hard against its mounting surface as it does against the air, and a single 3/4 inch panel flexes under that load, which smears output and works the driver loose over time.

The outer layer is machined as a flush recess to Audiomobile's 12.65 inch frame, so the driver bolts to the inner layer and sits flush with the gloss black acrylic insert.

Anechoic F3 is 44.0 Hz with system resonance at 47.3 Hz. At Qtc 0.77 the response carries a slight 0.1 dB lift near resonance and F3 sits just below fc, the classic punchy sealed alignment.

Those figures exclude cabin gain. In a car the transfer function of the cabin adds real output below 50 Hz, so in-vehicle response runs deeper than the numbers above. Audiomobile's sheet publishes no in-box F3 for this driver.

No. Polyfill is already installed as a light wall lining to control internal reflections, and the quantity is chosen so it does not change the acoustic volume.

Do not add more. Packing a sealed box with fill makes it behave as though it were larger, which walks the alignment away from the 0.90 cubic feet this cabinet was built to.

No driver. This is an enclosure only. You receive the cabinet finished in plush black carpet with the gloss black acrylic baffle insert, one side-mounted pre-wired terminal cup, the polyfill lining already in place, and the threaded insert kit with stainless machine screws.

The inserts ship loose on purpose: Audiomobile publishes no mounting hole locations for the Encore, so you set the driver in the recess, mark its holes, drill and press the inserts. The Audiomobile Encore 4412 is purchased separately, and the cabinet is cut direct fit to it, not a general purpose 12 inch box.