Performance Optimized Wedge Ported 12" Enclosure NVX NSW12v3 · Single 12" Ported enclosure

Sealed, the NSW12v3 needs 1.22 cubic feet net to reach a Qtc of 0.707. Vented, it trades that for deeper extension. The wedge's port runs 19.7 m/s in the channel and 12.4 at the flared mouth at NVX's 500 W rating, with the cone peaking at 7.1 of its 12.5 mm. Passband ripple is 0.8 dB. Tuning is chosen for in-car response rather than an anechoic curve: a vehicle adds roughly 12 dB per octave below about 45 Hz. In this cabinet that lands at 2.2 dB of in-car spread across 25 to 60 Hz.

The raked face is the seat side. A factory rear seat back leans about 20 degrees off vertical, so the cabinet sits flat against it and uses floor a square box wastes. The baffle stays vertical and fires rearward into the trunk, which acts as the acoustic extension into the cabin. This one is 14.14 inches deep at the base and 8.50 at the top, 30.00 wide and 15.5 tall.

Yes, at 27 Hz, 24 dB per octave. Below tuning a vented box stops loading the cone and excursion runs away toward DC. With the filter in place this cabinet puts the NVX NSW12v3 at 56 percent of its usable travel at full rated power; without it there is no meaningful number to quote.

NVX rate the NSW12v3 at 500 W RMS and that is the thermal ceiling. The Performance Graphs tab shows the mechanical limit, the power at which the cone reaches the end of its travel in this cabinet: here the cone sits at 56 percent of usable travel at the rating, so heat is what stops you, not travel. A D2 coil is 4 ohms in series or 1 ohm in parallel; run series unless the amplifier is rated for 1 ohm. A D4 is 8 series or 2 parallel.

Below about 24 Hz, yes. The sealed wedge we build for it is louder down there by up to 3.2 dB, because a sealed box rolls off gently where a vented one falls away steeply under tuning. Above that this alignment is the louder of the two for the same power. The Performance Graphs tab plots this cabinet against the 1.63 cu ft sealed wedge we build for this driver (PO 12-S W NSW).

It is a triangular slot in the bottom-rear corner: the floor and the raked back wall are two sides, one bevelled panel is the third. It runs across the cabinet, opens into the box through a 3.10 inch gap at the far end and exits through the side panel as the same triangle. Straight, no bend: 25.15 inches of path and 19.9 square inches of channel running at 19.7 metres per second, 51 percent of its turbulence limit. The three mouth edges are rounded over at 1/2 inch, so the opening at the face is 31.4 square inches and the air leaves it at 12.4 metres per second against the 17.0 threshold where a slot port starts to chuff; the panel's throat end is rounded at 3/8 inch for the same reason. The terminal cup is on the other side.

No, and do not add any. Every sealed Proline X enclosure ships with polyfill; a ported one must not, because damping changes the effective volume the port is tuned against. The port here is cut to 25.15 inches for 34.5 Hz. Stuff it and you move the tuning without shortening the port.

No. This is an enclosure only, cut for the NVX NSW12v3 specifically: the 10.860 inch cutout, the 6.000 inch mounting depth allowance and the 1.39 cubic foot alignment all come from NVX's published parameters. It fits both coil versions (D2 and D4), and the cabinet was checked against both. Bring your own driver.