AudioControl EPICX12 Box: Ported 12" Professional Series Enclosure Single 12" Ported enclosure

Sealed, the EPICX12 is listed in our sealed wedge (PO 12-S W EPICX12) at 1.25 cubic feet, Qtc 0.89, half power 41 Hz. The slot is gated at 600 W: the channel runs 20.0 m/s and the mouth 10.4, and the cone peaks at 7.6 of its 8.5 mm with the subsonic filter in place. Passband ripple is 2.3 dB. The EPICX12 D4 (dual 4 ohm) was run through the same cabinet: F3 38.8 Hz, passband ripple 2.6 dB, 7.5 of its 8.5 mm at 500 W. Tuning is chosen for in-car response rather than an anechoic curve: a vehicle adds roughly 12 dB per octave below about 45 Hz, and this tuning is where that sum comes out flattest across 25 to 60 Hz.

The EPICX12 also builds in the Performance Optimized ported wedge and ported down-fire, the smaller and cheaper boxes. The Professional cabinet is the step up for it: a 2.25 inch three-layer baffle with the woofer flush in the outer layer, and a slot port gated at 600 W. It carries a 2 year warranty, against 1 year on the Performance Optimized lines.

AudioControl does not publish the mounting hole locations for the EPICX12, so we cannot install the threaded inserts before it ships. The threaded insert kit comes in the box instead: inserts sized to the woofer, the correct drill bit, 2.5 inch allen-head screws, an allen key and woofer gasket tape. You set the inserts when you mount the woofer, and this box ships with one kit.

Yes, at 28 Hz, 24 dB per octave. Below tuning a vented box stops loading the cone and excursion runs away toward DC. With the filter in place this cabinet puts the AudioControl EPICX12 at 90 percent of its usable travel at 600 W.

Not one we can show you. We do not build a sealed enclosure for the AudioControl EPICX12 and AudioControl publish no sealed volume for it, so the Performance Graphs tab carries no ported-versus-sealed chart: the only sealed box left to plot would be this cabinet stuffed and sealed, which nobody would build, and a comparison against it would tell you nothing you could buy. What a vented box gives up is the region below tuning, where the cone unloads and the 28 Hz subsonic filter takes over; around 36.0 Hz the vent carries the load and cone travel drops to its minimum, which no sealed alignment can do.

It is a vertical slot beside the woofer, the full height of the cavity, 1.25 inches wide and 18.1 square inches. It runs 5.00 inches to the back wall and turns once along it for 12.78 inches; the fold costs about 1.5 Hz and the port is cut for it. The channel runs at 20.0 metres per second at 600 W, 49 percent of its turbulence limit, and the mouth edges carry a 1/2 inch roundover so the air leaves the face at 10.4 metres per second against the 17 metres per second threshold where a slot starts to chuff.

49 lb, 32.00" W x 16.00" H x 10.00" D external. Every Professional cabinet is priced the same way, by its size: this one is 2.96 cubic feet outside. Delivery to the 48 states is inside the price; it ships as a 49 lb parcel and checkout adds nothing. The $-13 difference is the larger box and the port this driver needs to run at its rating. Do not add polyfill; it ships dry on purpose.

No. This is an enclosure only, cut for the AudioControl EPICX12 specifically: the 11.000 inch cutout, the 6.000 inch mounting depth allowance and the 1.28 cubic foot alignment all come from AudioControl's published parameters. It fits both AudioControl versions, the EPICX12 D2 (dual 2 ohm) and the EPICX12 D4 (dual 4 ohm); the cabinet is tuned on the EPICX12 D2 and was run with the EPICX12 D4 too. Bring your own driver.